Diff for /wikisrc/ports/sandpoint/inststorcenter.mdwn between versions 1.1 and 1.2

version 1.1, 2013/10/31 21:05:10 version 1.2, 2015/09/04 22:22:18
Line 4  Introduction Line 4  Introduction
 <table>  <table>
 <tbody>  <tbody>
 <tr class="odd">  <tr class="odd">
 <td align="left"><p>This document describes in depth how to prepare your Iomega StorCenter G2 for installing OS/sandpoint. The three supported models are:</p>  <td align="left"><p>This document describes in depth how to prepare your Iomega StorCenter G2 for installing NetBSD/sandpoint. The three supported models are:</p>
 <ul>  <ul>
 <li>StorCenter G2 Single Drive, 200MHz</li>  <li>StorCenter G2 Single Drive, 200MHz</li>
 <li>StorCenter G2 Dual Drive, 200MHz</li>  <li>StorCenter G2 Dual Drive, 200MHz</li>
 <li>StorCenter G2 Quad Drive, 266MHz</li>  <li>StorCenter G2 Quad Drive, 266MHz</li>
 </ul>  </ul>
 <p>All models have 64 MB RAM and a PATA disk interface. Note that newer StorCenter models use an ARM CPU and are not supported.</p>  <p>All models have 64 MB RAM and a PATA disk interface. Note that newer StorCenter models use an ARM CPU and are not supported.</p>
 <p>To install OS/sandpoint you will have to open the case for getting access to the serial console. This is shown here for the Single Drive model.</p></td>  <p>To install NetBSD/sandpoint you will have to open the case for getting access to the serial console. This is shown here for the Single Drive model.</p></td>
 <td align="left"><img src="../../images/ports/sandpoint/iomega_portrait.jpg" alt="StorCenter Single Drive" /></td>  <td align="left"><img src="../../images/ports/sandpoint/iomega_portrait.jpg" alt="StorCenter Single Drive" /></td>
 </tr>  </tr>
 </tbody>  </tbody>
Line 148  using [U-Boot](http://www.denx.de/wiki/U Line 148  using [U-Boot](http://www.denx.de/wiki/U
 Loader.  Loader.
   
 Now you can connect with any terminal program to the StorCenter's serial  Now you can connect with any terminal program to the StorCenter's serial
 console. The easiest approach may be to use OS's `tip(1)` command to  console. The easiest approach may be to use NetBSD's `tip(1)` command to
 make a direct console connection at 115200bps.  make a direct console connection at 115200bps.
   
     # tip -115200 console      # tip -115200 console
Line 181  altboot Line 181  altboot
 -------  -------
   
 The `altboot(8)` utility functions as a bridge between the Iomega  The `altboot(8)` utility functions as a bridge between the Iomega
 firmware and the OS kernel startup environment. NAS firmware often  firmware and the NetBSD kernel startup environment. NAS firmware often
 provides no means to boot a kernel from disk or from the network and  provides no means to boot a kernel from disk or from the network and
 doesn't initialize all hardware correctly. We will also use it to pass a  doesn't initialize all hardware correctly. We will also use it to pass a
 bootinfo list to the kernel.  bootinfo list to the kernel.
Line 226  Boot the INSTALL kernel with altboot Line 226  Boot the INSTALL kernel with altboot
 ------------------------------------  ------------------------------------
   
 Now you can use `altboot` to launch the `netbsd-INSTALL` kernel for  Now you can use `altboot` to launch the `netbsd-INSTALL` kernel for
 installing OS. You may choose to load it with TFTP or from NFS. For TFTP  installing NetBSD. You may choose to load it with TFTP or from NFS. For TFTP
 you have to enable `tftpd(8)` in `/etc/inetd.conf`, and for NFS there is  you have to enable `tftpd(8)` in `/etc/inetd.conf`, and for NFS there is
 a documentation at [The Network File  a documentation at [The Network File
 System](http://www.&os;.org/docs/guide/en/chap-net-services.html#chap-net-services-nfs).  System](http://www.&os;.org/docs/guide/en/chap-net-services.html#chap-net-services-nfs).
Line 243  appropriate `dhcpd.conf` entry could loo Line 243  appropriate `dhcpd.conf` entry could loo
   
 The `root-path` option is only needed when using NFS and should match  The `root-path` option is only needed when using NFS and should match
 your exported NFS directory. Uncompress `netbsd-INSTALL.gz` from the  your exported NFS directory. Uncompress `netbsd-INSTALL.gz` from the
 OS/sandpoint distribution and copy it into the NFS or TFTP directory.  NetBSD/sandpoint distribution and copy it into the NFS or TFTP directory.
 Then start the DHCP, NFS or TFTP server and boot the installation kernel  Then start the DHCP, NFS or TFTP server and boot the installation kernel
 from the firmware either with  from the firmware either with
   
Line 258  the kernel via network and launches it: Line 258  the kernel via network and launches it:
   
     ## Starting application at 0x01000000 ...      ## Starting application at 0x01000000 ...
   
     >> OS/sandpoint altboot, revision 1.8 (Wed Nov 23 21:51:40 CET 2011)      >> NetBSD/sandpoint altboot, revision 1.8 (Wed Nov 23 21:51:40 CET 2011)
     >> IOMEGA StorCenter G2, cpu 200 MHz, bus 100 MHz, 64MB SDRAM      >> IOMEGA StorCenter G2, cpu 200 MHz, bus 100 MHz, 64MB SDRAM
     channel 0 present      channel 0 present
     wd0: <ST3300822A> DMA LBA LBA48 286168 MB      wd0: <ST3300822A> DMA LBA LBA48 286168 MB
Line 270  the kernel via network and launches it: Line 270  the kernel via network and launches it:
     entry=0x90000, ssym=0x5a66f0, esym=0x5a6b78      entry=0x90000, ssym=0x5a66f0, esym=0x5a6b78
     Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,      Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
         2006, 2007, 2008, 2009, 2010, 2011          2006, 2007, 2008, 2009, 2010, 2011
         The OS Foundation, Inc.  All rights reserved.          The NetBSD Foundation, Inc.  All rights reserved.
     Copyright (c) 1982, 1986, 1989, 1991, 1993      Copyright (c) 1982, 1986, 1989, 1991, 1993
         The Regents of the University of California.  All rights reserved.          The Regents of the University of California.  All rights reserved.
   
     OS 5.99.59 (INSTALL) #10: Fri Dec 30 18:53:09 CET 2011      NetBSD 5.99.59 (INSTALL) #10: Fri Dec 30 18:53:09 CET 2011
         frank@compaq.owl.de:/home/frank/netbsd/current/src/sys/arch/sandpoint/compile/obj/INSTALL          frank@compaq.owl.de:/home/frank/netbsd/current/src/sys/arch/sandpoint/compile/obj/INSTALL
     Model: iomega      Model: iomega
     total memory = 65536 KB      total memory = 65536 KB
Line 333  the kernel via network and launches it: Line 333  the kernel via network and launches it:
     erase ^H, werase ^W, kill ^U, intr ^C, status ^T      erase ^H, werase ^W, kill ^U, intr ^C, status ^T
     Terminal type? [vt100]      Terminal type? [vt100]
   
 Just follow the usual procedure to install a OS system.  Just follow the usual procedure to install a NetBSD system.
   
 Sandpoint installation window  Sandpoint installation window
 Post installation steps  Post installation steps
Line 380  reboot: Line 380  reboot:
 The `\` is important for `setenv` not to misinterpret the `;` as the end  The `\` is important for `setenv` not to misinterpret the `;` as the end
 of the command.  of the command.
   
 Have fun with your mini OS server!  Have fun with your mini NetBSD server!

Removed from v.1.1  
changed lines
  Added in v.1.2


CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb