File:  [NetBSD Developer Wiki] / wikisrc / ports / sandpoint / instlinkstation.mdwn
Revision 1.1: download - view: text, annotated - select for diffs
Thu Oct 31 21:05:10 2013 UTC (16 months, 4 weeks ago) by mspo
Branches: MAIN
CVS tags: HEAD
fix sandpoint links


<tr class="odd">
<td align="left"><p>This document describes in depth how to prepare your Buffalo LinkStation for installing OS/sandpoint. In this example we use a LinkStation HD-HLAN, which is the same board as a classic KuroBox. The software installation instructions are valid for the whole LinkStation/KuroBox family:</p>
<li>LinkStation HD-HLAN (LS1/PPC)</li>
<li>LinkStation HD-HGLAN (Gigabit ethernet)</li>
<li>TeraStation HD-HTGL</li>
<li>TeraStation Pro TS-TGL</li>
<li>KuroBox classic (HD-HLAN board)</li>
<li>KuroBox HG (HD-HGLAN board)</li>
<li>KuroBox/T4 (TS-TGL board)</li>
<td align="left"><img src="../../images/ports/sandpoint/ls1_front.jpg" alt="HD-HLAN front view" /></td>

Accessing the serial interface

We need a serial console to get access to the firmware. That includes
soldering a four pin header onto the board and building (or buying) a
serial adapter from the LinkStation's TTL levels to RS232 levels.

Disassemble the HD-HLAN

Unfortunately the LinkStation was not meant to be opened by customers,
so Buffalo didn't make it easy. On the top and bottom of the case there
is a small tab besides the grey frame, which you have to press down
(e.g. with a screwdriver) to be able to move the frame to the front. On
the photo below the location is marked red.

KuroBox with tab marked
After a few millimeters the grey piece snaps free and comes up. You need
quite some force to do that, because the shiny front bezel is secured by
two hidden screws (one in the top and another in the bottom of the
bezel). With enough force and skill you may be able to tear the screws
out of the case (fortunately the screws are small). They remain in the
shiny bezel. You may want to shorten the screws with a file now.

HD-HLAN half opened
Before the case can be opened you have to remove a screw hidden under a
sticker, below the fan (marked on the right side of the picture). Then
press the four tabs on the top and bottom to remove the upper half of
the case. Remove another four screws to be able to lift the board.

Locate the serial header

Look out for a 4-pin header, called `J1`, which is usually unpopulated.
The pin assignments are:

<tr class="odd">
<td align="left"><table>
<tr class="odd">
<td align="left"><strong>Pin number</strong></td>
<td align="left"><strong>Function</strong></td>
<tr class="even">
<td align="left">1</td>
<td align="left">TXD</td>
<tr class="odd">
<td align="left">2</td>
<td align="left">RXD</td>
<tr class="even">
<td align="left">3</td>
<td align="left">3.3V</td>
<tr class="odd">
<td align="left">4</td>
<td align="left">GND</td>
<td align="left"><img src="../../images/ports/sandpoint/ls1_ser_pins.jpg" alt="Header pin assignments" /></td>

Solder the missing header and enable write access

I would suggest to solder the 4-pin header on the back side of the PCB,
because it is better accessible when opening the case. It is advisable
to use an angled header to avoid problems closing the case. You also
have to bridge `R76`, which is unoccupied. This is needed to enable
write-access for the serial console. You may want to mark pin 1 of the
header, before installing the board again.

<tr class="odd">
<td align="left"><img src="../../images/ports/sandpoint/ls1_ser_header.jpg" alt="Soldered header" /></td>
<td align="left"><img src="../../images/ports/sandpoint/ls1_R76.jpg" alt="Bridging R76" /></td>

Connect a serial cable

The serial port on LinkStation and KuroBox devices is using 3.3V TTL
levels, which have to be converted into regular RS232 levels by a level
shifter circuit. If you are not anxious using a soldering iron you find
detailed instructions how to build such a converter here:

-   Serial adapter for 3.3V TTL

Make sure that the layout of the plug fits to the pinout of the
LinkStation's serial header, as shown above.

Another option is to buy such a converter. There are solutions for a
standard RS232 interface and for an USB interface. Look out for:

-   RS232 level shifter / breakout board (MAX3232 based)
-   USB to TLL serial level shifter / breakout board (FT232 based)

Now you can connect with any terminal program to the LinkStation's
serial console. The easiest approach may be to use OS's `tip(1)` command
to make a direct console connection at 57600bps.

    # tip -57600 console

Note that when using a serial connection via USB you may have to make an
entry for `/dev/ttyU0` in `/etc/remote`.

Replace the firmware with U-Boot

The LinkStations run with a proprietary firmware, which doesn't give you
any control about the boot process. So our next step is to replace it
with [U-Boot](

Getting root access

We need root access on the vendor's Linux installation to be able to
flash a new firmware. Without the original disk it will become much more
difficult. You would either have to find a way to install the system
onto a new disk with the help of a second machine, or use the JTAG port
to flash the new firmware directly into the chip (in the last case you
can skip all sections until ?).

For the KuroBox you can skip this section. The root password is known to
be `kuro`. Also telnet access is enabled. The default IP of the KuroBox
is ``.

Make a new user over the LinkStation's web interface. We can use it to
log in over the serial port.

Add a new user on the GUI
Log in into the new account and create a CGI file under `/www` which
makes `/etc/passwd` writeable for all users.

    BUFFALO INC. Link Station series HD-HLAN (HIDETADA)

    BUFFALO login: 
    Linux (none) 2.4.17_mvl21-sandpoint #990 2004xxxx 13:39:00 JST ppc unknown

`exploit.cgi` should look like this:

    chmod 666 /etc/passwd

Then enter the URL `http://mylinkstation/cgi-bin3/exploit.cgi` into your
browser. When all went well, `/etc/passwd` is writeable now. Edit it
with `vi` and copy your user password (`/Jg58Gq9427qY` in this example)
over the current root password. Now you can log in with the same
password into the root account.


The CGI exploit, which I described above, probably does not work with
all Linkstation firmware releases. It may fail with versions after 1.45.
I was able to do it with 1.47 though. An alternative to this method
would be to connect the hard disk to a second machine, which can mount
the Linux file system, and replace the root password there.

Flashing U-Boot

To transfer the new firmware onto the LinkStation we first have to
configure FTP access (already enabled for KuroBox). Enable the server
and allow write access for registered users to the shared folders (e.g.

Enable FTP access with the GUI
Get an appropriate U-Boot firmware image from

-   LinkStation HD-HLAN or KuroBox classic
-   LinkStation HD-HGLAN or KuroBox HG

Transfer the firmware into the `share` folder on the LinkStation.

    Connected to
    220 BUFFALO FTP server ready
    Name ( 
    331 Password required for Besucher.
    230 User Besucher logged in.
    Remote system type is UNIX.
    Using binary mode to transfer files.
    250 CWD command successful.
    local: u-boot-hd.flash.bin remote: u-boot-hd.flash.bin
    229 Entering Extended Passive Mode (|||1045|)
    150 Opening BINARY mode data connection for u-boot-hd.flash.bin
    100% |***********************************|   170 KiB    6.07 MiB/s    00:00
    226 Transfer complete.
    174640 bytes sent in 00:00 (4.86 MiB/s)

The next step is dangerous. Any fault, like a wrong firmware or an
interrupted flashing process, will turn your LinkStation into a brick.

The boot loader firmware can be accessed from Linux through `/dev/fl2`.
There is no `dd` so we will use `cat`. Log in as root on the serial
console, go to the shared folder where we uploaded the new firmware and
flash it.

    total 176
    -rw-rw-rw-    1 Besucher hdusers    174640 May 13 15:43 u-boot-hd.flash.bin

The Diag and Disk Full LEDs will flash red during this process. This is
normal. After a few seconds the LEDs are off again and the prompt
returns. To make sure the process was successful, you should reread the
firmware from the flash and compare it with the original. Therefore you
have to download the new image, as this Linux installation also got no


Here the downloaded image differs at character 174641. But that is ok,
because the firmware is only 174640 bytes large and we downloaded the
whole flash contents.

    cmp: EOF on u-boot-hd.flash.bin: char 174641, line 891

Reboot your LinkStation and cross fingers. When all went well, the
following lines will appear on your serial console:

    U-Boot 1.1.4 LiSt 2.1.0 (Sep 21 2006 - 00:22:56) LinkStation / KuroBox

    CPU:   MPC8245 Revision 1.4 at 196.608 MHz: 16 kB I-Cache 16 kB D-Cache
    DRAM:  64 MB
    FLASH:  4 MB
    *** Warning - bad CRC, using default environment

            00  0b  1317  0985  0200  ff
            00  0c  1095  0680  0101  ff
            00  0e  1033  0035  0c03  ff
            00  0e  1033  0035  0c03  ff
            00  0e  1033  00e0  0c03  ff
    Net:   COMET#0

This precompiled U-Boot defaults to the `netcat` console. So we have to
wait about 20 seconds before an error is printed and the console returns
to serial.

    next_cons_choice: Unexpected code: 0x33
    stdin :   serial
    stdout:   serial
    stderr:   serial
    IDE:   Bus 0: OK 
      Device 0: Model: SAMSUNG SP1604N Firm: TM100-30 Ser#: S013J20XC0xxxx
                Type: Hard Disk
                Supports 48-bit addressing
                Capacity: 152627.8 MB = 149.0 GB (312581808 x 512)
    Boot in 08 seconds ('s' to stop)...

Here you should press `s` to stop booting and change some environment
variables to make U-Boot default to serial.


Enter `reset` to reboot into interactive mode with serial console. At
this point we no longer need the original Linux installation and we are
ready for OS.

First installation

The altboot bootloader

The `altboot(8)` program functions as a bridge between the U-Boot
firmware and the OS kernel startup environment. NAS firmware often
provides no means to boot a kernel from disk or from the network and
doesn't initialize all hardware correctly. We will also use it to pass a
bootinfo list to the kernel.

The `altboot` boot loader has to be loaded and started using U-Boot. For
the first installation we have to load it over the network with TFTP
protocol, using the command `tftpboot`. Later we can put `altboot` into
the flash memory and copy it from there.

When not already done, enable TFTP on your working system in
`/etc/inetd.conf` and restart `inetd`. Then copy `altboot.bin` from the
sandpoint distribution into `/tftpboot`. On the LinkStation we have to
tell U-Boot its client address and the `tftpd` server address. Our
working system's server address is `` in this example, and
the LinkStation is at ``.

    Saving Environment to Flash...
    Un-Protected 1 sectors
    Erasing Flash...
    Flash erase: first = 54 @ 0xfff60000
                 last  = 54 @ 0xfff60000
    Flash erase: Done
    Erased 1 sectors
    Writing to Flash... done
    Protected 1 sectors

Load `altboot.bin` into memory. The binary is relocated at 0x1000000, so

    Using COMET#0 device
    TFTP from server; our IP address is
    Filename 'altboot.bin'.
    Load address: 0x1000000
    Loading: ##############
    Bytes transferred = 70844 (114bc hex)

Boot the INSTALL kernel with altboot

Now you can use `altboot` to launch the `netbsd-INSTALL_KURO` kernel for
installing OS. It is important to take `netbsd-INSTALL_KURO` instead of
`netbsd-INSTALL`, because LinkStation and KuroBox systems have the UARTs
swapped, i.e. they are using the second UART for the serial console. You
may choose to load the installation kernel with TFTP or from NFS. TFTP
was described above and for NFS there is a documentation at [The Network
But in both cases you have to set up a DHCP server, which is explained
in the [DHCP Howto]( An
appropriate `dhcpd.conf` entry could look like this:

            host linkstation {
                    hardware ethernet 00:07:40:xx:xx:xx;
                    option root-path "/export/linkstation/root";

The `root-path` option is only needed when using NFS and should match
your exported NFS directory. Uncompress `netbsd-INSTALL_KURO.gz` from
the OS/sandpoint distribution and copy it into the NFS or TFTP
directory. Then start the DHCP, NFS or TFTP server and boot the
installation kernel from the firmware either with


or from NFS:


Our bootloader configures the hardware, determines the IP address, loads
the kernel via network and launches it:

    ## Starting application at 0x01000000 ...

    >> NetBSD/sandpoint altboot, revision 1.5 (Fri Feb 18 23:21:15 CET 2011)
    >> KuroBox, cpu 195 MHz, bus 97 MHz, 64MB SDRAM
    channel 0 present
    wd0: <SAMSUNG SP1604N> DMA LBA LBA48 152627 MB
    wd0: no disklabel
    MAC address 00:07:40:xx:xx:xx
    loading "netbsd-INSTALL_KURO" 5142988+110988=0x502f98
    entry=0x00090000, ssym=0x00592b58, esym=0x00592f98
    ksyms: Symbol table not found
    ksyms: String table not found
    ksyms: Perhaps the kernel is stripped?
    Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
        2006, 2007, 2008, 2009, 2010, 2011
        The NetBSD Foundation, Inc.  All rights reserved.
    Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.

    NetBSD 5.99.45 (INSTALL_KURO) #0: Thu Feb 10 11:36:46 UTC 2011
    total memory = 65536 KB
    avail memory = 57984 KB
    OpenPIC Version 1.2: Supports 1 CPUs and 26 interrupt sources.
    mainbus0 (root)
    cpu0 at mainbus0: 8245 (Revision 0.4), ID 0 (primary)
    cpu0: HID0 0x90c000<DOZE,DPM,ICE,DCE>, powersave: 1
    eumb0 at mainbus0
    com0 at eumb0 unit 1: ns16550a, working fifo
    com0: console
    ociic0 at eumb0
    iic0 at ociic0: I2C bus
    rs5c372rtc0 at iic0 addr 0x32: RICOH RS5C372[AB] Real-time Clock
    satmgr0 at eumb0 unit 0: button manager (kurobox)
    pci0 at mainbus0 bus 0
    pchb0 at pci0 dev 0 function 0
    pchb0: vendor 0x1057 product 0x0006 (rev. 0x14)
    tlp0 at pci0 dev 11 function 0: ADMtek AN985 Ethernet, pass 1.1
    tlp0: interrupting at irq 16
    tlp0: Ethernet address 00:07:40:xx:xx:xx
    ukphy0 at tlp0 phy 1: OUI 0x00e092, model 0x0001, rev. 1
    ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    cmdide0 at pci0 dev 12 function 0: Silicon Image 0680 (rev. 0x02)
    cmdide0: primary channel wired to native-PCI mode
    cmdide0: using irq 17 for native-PCI interrupt
    atabus0 at cmdide0 channel 0
    cmdide0: secondary channel wired to native-PCI mode
    atabus1 at cmdide0 channel 1
    ohci0 at pci0 dev 14 function 0: vendor 0x1033 product 0x0035 (rev. 0x43)
    ohci0: interrupting at irq 19
    ohci0: OHCI version 1.0
    usb0 at ohci0: USB revision 1.0
    ohci1 at pci0 dev 14 function 1: vendor 0x1033 product 0x0035 (rev. 0x43)
    ohci1: interrupting at irq 19
    ohci1: OHCI version 1.0
    usb1 at ohci1: USB revision 1.0
    ehci0 at pci0 dev 14 function 2: vendor 0x1033 product 0x00e0 (rev. 0x04)
    ehci0: interrupting at irq 19
    ehci0: companion controllers, 3 ports each: ohci0 ohci1
    usb2 at ehci0: USB revision 2.0
    biomask 8000038 netmask 8000038 ttymask 8000038
    uhub0 at usb0: vendor 0x1033 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub1 at usb1: vendor 0x1033 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
    uhub2 at usb2: vendor 0x1033 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
    wd0 at atabus0 drive 0: <SAMSUNG SP1604N>
    wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
    boot device: tlp0
    root on md0a dumps on md0b
    root file system type: ffs
    erase ^H, werase ^W, kill ^U, intr ^C, status ^T
    Terminal type? [vt100]

Just follow the usual procedure to install a OS system.

Sandpoint installation window
Post installation steps

After a successful installation you want to make the system boot
standalone when switched on, without the need for a serial console. So
you have to modify the `bootcmd` in U-Boot's environment and write the
`altboot.bin` binary to the Flash ROM.

On the LinkStation and KuroBox the last 128K or the Flash ROM are known
to be unused, so we can put `altboot` there. Load `altboot.bin` into
memory at `0x1000000` again, as explained above, and execute the
following commands to write it to Flash ROM:

    Un-Protected 9 sectors

    Flash erase: first = 62 @ 0xfffe0000
                 last  = 70 @ 0xffffe000
    Flash erase: Done
    Erased 9 sectors
    Using COMET#0 device
    TFTP from server; our IP address is
    Filename 'altboot.bin'.
    Load address: 0x1000000
    Loading: ##############
    Bytes transferred = 70844 (114bc hex)
    Copy to Flash... done
    Total of 131072 bytes were the same
    Protected 9 sectors

Finally adapt the `bootcmd` environment string to autoboot `altboot` and
start the `netbsd` kernel (which is the default name) from `wd0` on each


The `\` is important for `setenv` not to misinterpret the `;` as the end
of the command.

Have fun with your mini OS server!

CVSweb for NetBSD wikisrc <> software: FreeBSD-CVSweb