Diff for /wikisrc/ports/mvmeppc.mdwn between versions 1.1 and 1.9

version 1.1, 2012/12/19 03:50:46 version 1.9, 2016/06/21 09:32:43
Line 1 Line 1
 [[!template id=port  [[!template id=port
 port="mvmeppc"  port="mvmeppc"
 cur_rel="6.0"    cur_rel="7.0.1"
 future_rel="7.0"  future_rel="8.0"
 changes_cur="6.0"  pkg_rel="6.0"
 changes_future="7.0"  changes_cur="7.0"
 thumbnail="http://www.netbsd.org/images/ports/mvmeppc/mvme2600.gif"  thumbnail="http://www.netbsd.org/images/ports/mvmeppc/mvme2600.gif"
 about="""  about="""
 NetBSD/mvmeppc is the port of NetBSD to Motorola's PowerPC VME Single Board  NetBSD/mvmeppc is the port of NetBSD to Motorola's PowerPC VME Single Board
Line 17  recent boards will be added as and when  Line 18  recent boards will be added as and when 
 developers.  developers.
 """  """
 supported_hardware="""  supported_hardware="""
 ###Supported System Models  ##Supported System Models
 * MVME160x family   * MVME160x family 
 ###Boot Options  ##Boot Options
 'Supported:'  **Supported:**
 * network  * network
 'Unsupported:'  **Unsupported:**
 * disk  * disk
Line 35  supported_hardware=""" Line 36  supported_hardware="""
 """  """
 additional="""  additional="""
 ###What are the jumpers on the backplane  * [NetBSD/mvmeppc FAQ](http://www.NetBSD.org/ports/mvmeppc/faq.html)
   * [NetBSD/mvmeppc History](http://www.NetBSD.org/ports/mvmeppc/history.html)
 The jumpers on the backplane are for Bus Grant and Interrupt Acknowledge. Some  
 VMEbus boards, like disk controllers, do their own VMEbus I/O instead of using  
 DMA from the CPU. The I/O board requests control of the VMEbus, the arbiter on  
 the CPU board releases control of the VMEbus, and then the arbiter on the CPU  
 sends a Bus Grant signal down the backplane.  
 There are only 4 Bus Grant levels, and you can have several boards, on the same  
 Bus Grant level. The Bus Grant signal daisy-chains down the backplane through  
 each I/O board. If you have an empty slot you break the daisy-chain.  
 Backplane manufacturers put jumper pins next to the connectors so you can jumper  
 across empty slots. Unfortunately the jumpers may be to the right or left of a  
 slot depending on the manufacturer.  
 You may also find that some VMEbus boards don't pass on daisy-chain signals that  
 they don't use. This means that you may have to leave jumpers on even when a  
 board is in a slot.  
 If the boards are side-by-side without an empty slot between the CPU and the  
 VMEbus boards you may not need any jumpers. That might be worth a try.   
 Using NetBSD/prep as a base, NetBSD was ported to an MVME1603-051 by Steve  
 Woodford. The board was one of two donated to the NetBSD Foundation by Gan  
 Starling on the condition that a port be attempted.  
 Following receipt of the boards, and replacement of the VxWorks bootcode by a  
 PPCBUG image kindly provided by Motorola Computer Group, NetBSD/mvmeppc was up  
 and running multi-user within two weeks.   
 """  """
 ]]  ]]
 [[!tag tier2port]]  [[!tag tier2port]]

Removed from v.1.1  
changed lines
  Added in v.1.9

CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb