--- wikisrc/ports/hp300.mdwn	2014/01/13 08:05:07	1.2
+++ wikisrc/ports/hp300.mdwn	2018/07/19 10:15:06	1.19
@@ -1,15 +1,15 @@
 [[!template id=port
 port="hp300"
-cur_rel="6.0"  
-future_rel="7.0"
-changes_cur="6.0"
-changes_future="7.0"
+cur_rel="8.0"
+future_rel="9.0"
+pkg_rel="6.0"
+changes_cur="8.0"
+changes_future="9.0"
 thumbnail="http://www.netbsd.org/images/ports/hp300/320.gif"
 about="""
 NetBSD/hp300 is the port of NetBSD to Hewlett-Packard 9000 Series 300 and 400
 workstations. It runs on almost all workstations from this generation. Series
-700 and 800 workstations are not currently supported, but work is underway on
-[[NetBSD/hp700|hp700]].
+700 and 800 workstations are supported by [[NetBSD/hppa|hppa]].
 
 NetBSD/hp300 is based on work done by David P. Davis at the University of
 California, Berkeley and the Systems Programming Group at the University of Utah
@@ -23,12 +23,12 @@ exist.
 supported_hardware="""
 All systems with a FPU are supported in NetBSD/hp300 (this excludes the 310 and
 332). Systems marked with a "*" do not support the built-in framebuffer. You
-will need to [set up a serial console](ports/hp300faq.html#serial400) on these
+will need to [[set up a serial console|hp300faq#serial400]] on these
 machines.
 
 The minimal configuration for a NetBSD/hp300 system requires 4M of RAM and about
 40M of disk space. For a full installation (including source and X11), at least
-8M of RAM and 200M of disk space are recommended. 
+8M of RAM and 200M of disk space are recommended.
 
 ###Supported Systems
 * 320
@@ -48,14 +48,14 @@ The minimal configuration for a NetBSD/h
 * 433s, 433t, 433dl
 
 'note'
-  > Series 400 machines must be configured in ["HP-UX Compatible Boot Mode".
-  > Follow these instructions](ports/hp300faq.html#domaintohpux) in the FAQ.
+  > Series 400 machines must be configured in [["HP-UX Compatible Boot Mode".
+  > Follow these instructions|hp300faq#domaintohpux]] in the FAQ.
 
 Some specific configurations of the above models don't support a local console.
 The 425e (and some rare 4XXt and 4XXdl machines) have their graphics device on
 the SGC bus, which is currently unsupported. Also, to use local console on a
 Series 400 workstation, you must currently use a HP-HIL keyboard/mouse (instead
-of Domain keyboard/mouse). 
+of Domain keyboard/mouse).
 
 ###Supported Hardware
 Devices (driver names in parenthesis) supported by NetBSD/hp300 include (list may not be complete):
@@ -183,7 +183,7 @@ for the console.
 Here are a few links that might be of interest to anyone with HP hardware not
 supported by NetBSD/hp300:
 
-* [NetBSD/hp700](ports/hp700)
+* [NetBSD/hppa](ports/hppa)
 * [HP9000/300 Linux](http://www.tazenda.demon.co.uk/phil/linux-hp/)
 * [Apollo Frequently Asked Questions](http://mit.edu/kolya/www/csa-faq.html)
 * [Apollo/DOMAIN Computer Info](http://www.zepa.net/apollo/)