Diff for /wikisrc/ports/evbarm/rockchip.mdwn between versions 1.2 and 1.6

version 1.2, 2015/03/29 21:25:53 version 1.6, 2020/01/08 06:48:19
Line 1 Line 1
 [[!meta title="NetBSD/evbarm on Rockchip SoCs"]]  [[!meta title="NetBSD/evbarm on Fuzhou RockChip SoCs"]]
   NetBSD supports several boards based on RockChip SoCs. Starting with NetBSD 9.0, FDT is used to configure devices. As a result, a large number of boards and configurations can be supported with a single kernel.
   <img src="https://pbs.twimg.com/media/ENlmzo7UUAIfSM6.jpg" width="300">
 [[!toc levels=2]]  [[!toc levels=2]]
 # Supported boards  # Supported SoCs
  - [MINIX NEO X7](http://www.minix.com.hk/Products/MINIX-NEOX7-ANDROID-TV.html)  
  - [Radxa Rock 2013/Pro/Lite](http://radxa.com/Rock)  <table>
  - [Rayeager PX2](http://en.chipspark.com/goods/Rayeager%20PX2%20Board/13)    <thead>
         <th>NetBSD version</th>
         <th>Example boards</th>
       <tr><td>RK3328</td><td>Rock64</td><td>9.0</td><td><a href="https://www.pine64.org/devices/single-board-computers/rock64/">Pine64 Rock64</a><td></td></tr>
       <tr><td>RK3399</td><td>Rock64</td><td>9.0</td><td><a href="https://www.pine64.org/rockpro64/">Pine64 RockPro64</a>, <a href="https://www.pine64.org/pinebook-pro/">Pine64 Pinebook Pro</a><td></td></tr>
   Other systems may work, but they have not been tested.
 # Supported hardware  # Supported hardware
  - SoCs  
    - Cortex-A9: PX2/RK3066 (dual core), RK3188/RK3188+ (quad core)  Please refer to the [GENERIC64 (64-bit)](https://nxr.netbsd.org/xref/src/sys/arch/evbarm/conf/GENERIC64) kernel configs for the most up-to-date list of supported hardware.
  - CPU frequency/voltage scaling (RK3188/RK3188+)  
  - SD/MMC controller  <table>
  - GPIO    <thead>
  - UART      <tr>
  - I2C        <th>Device</th>
  - PMU        <th>Supported</th>
    - ACT8834        <th>Notes</th>
  - Watchdog timer      </tr>
  - USB host (DWC2)    </thead>
  - Ethernet    <tbody>
  - RTC      <tr><td>Audio codec</td><td>Yes</td><td></td></tr>
       <tr><td>Framebuffer</td><td>Yes</td><td>Uses simplefb configured by bootloader</td></tr>
       <tr><td>Gigabit Ethernet</td><td>Yes</td><td></td></tr>
       <tr><td>Thermal sensors</td><td>Yes</td><td></td></tr>
       <tr><td>USB 2.0</td><td>Yes</td><td></td></tr>
       <tr><td>USB 3.0</td><td>Yes</td><td></td></tr>
       <tr><td>Watchdog timer</td><td>Yes</td><td></td></tr>
   # Installation
   - Download or build **arm64.img** (64-bit) from NetBSD 9.0 or later
   - Write the image to disk: **dd if=armv7.img of=/dev/rld0d bs=1m conv=sync**
   - Install a board-specific U-Boot (2018.05 or later) from pkgsrc to the SD card
     **dd if=/usr/pkg/share/u-boot/&lt;boardname&gt;/rkspi_loader.img of=/dev/rld0d seek=64 conv=sync**
   If your SoC has a SATA controller and you would like to install on
   an hard disk and use a SD card only for u-boot please give a look
   [[NetBSD/evbarm install via sysinst(8) on a SATA hard disk, USB stick or (u)SD card|ports/evbarm/install_using_sysinst]].
   # Tips and tricks
   # Links
   - [[NetBSD/evbarm install via sysinst(8) on a SATA hard disk, USB stick or (u)SD card|ports/evbarm/install_using_sysinst]]

Removed from v.1.2  
changed lines
  Added in v.1.6

CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb