--- wikisrc/ports/evbarm/rockchip.mdwn	2015/01/05 11:04:28	1.1
+++ wikisrc/ports/evbarm/rockchip.mdwn	2020/01/08 06:50:41	1.7
@@ -1,21 +1,83 @@
-[[!meta title="NetBSD/evbarm on Rockchip SoCs"]]
+[[!meta title="NetBSD/evbarm on Fuzhou RockChip SoCs"]]
+
+NetBSD supports several boards based on RockChip SoCs. Starting with NetBSD 9.0, FDT is used to configure devices. As a result, a large number of boards and configurations can be supported with a single kernel.
+
+<img src="https://pbs.twimg.com/media/ENlmzo7UUAIfSM6.jpg" width="300">
 
 [[!toc levels=2]]
 
-# Supported boards
- - [MINIX NEO X7](http://www.minix.com.hk/Products/MINIX-NEOX7-ANDROID-TV.html)
- - [Radxa Rock 2013/Pro/Lite](http://radxa.com/Rock)
- - [Rayeager PX2](http://en.chipspark.com/goods/Rayeager%20PX2%20Board/13)
+# Supported SoCs
+
+<table>
+  <thead>
+    <tr>
+      <th>Family</th>
+      <th>SoC</th>
+      <th>NetBSD version</th>
+      <th>Example boards</th>
+      <th>Notes</th>
+    </tr>
+  </thead>
+  <tbody>
+    <tr><td>RK3328</td><td>Rock64</td><td>9.0</td><td><a href="https://www.pine64.org/devices/single-board-computers/rock64/">Pine64 Rock64</a><td></td></tr>
+    <tr><td>RK3399</td><td>Rock64</td><td>9.0</td><td><a href="https://www.pine64.org/rockpro64/">Pine64 RockPro64</a>, <a href="https://www.pine64.org/pinebook-pro/">Pine64 Pinebook Pro</a><td></td></tr>
+  </tbody>
+</table>
+
+Other systems may work, but they have not been tested.
 
 # Supported hardware
- - SoCs
-   - Cortex-A9: PX2/RK3066 (dual core), RK3188/RK3188+ (quad core)
- - CPU frequency/voltage scaling (RK3188/RK3188+)
- - SD/MMC controller
- - GPIO
- - UART
- - I2C
- - PMU
-   - ACT8834
- - Watchdog timer
- - USB host (DWC2)
+
+Please refer to the [GENERIC64 (64-bit)](https://nxr.netbsd.org/xref/src/sys/arch/evbarm/conf/GENERIC64) kernel configs for the most up-to-date list of supported hardware.
+
+<table>
+  <thead>
+    <tr>
+      <th>Device</th>
+      <th>Supported</th>
+      <th>Notes</th>
+    </tr>
+  </thead>
+  <tbody>
+    <tr><td>Audio codec</td><td>Yes</td><td></td></tr>
+    <tr><td>Framebuffer</td><td>Yes</td><td>Uses simplefb configured by bootloader</td></tr>
+    <tr><td>Gigabit Ethernet</td><td>Yes</td><td></td></tr>
+    <tr><td>GPIO</td><td>Yes</td><td></td></tr>
+    <tr><td>GPU</td><td>-</td><td></td></tr>
+    <tr><td>I2C</td><td>Yes</td><td></td></tr>
+    <tr><td>I2S/PCM</td><td>Experimental</td><td></td></tr>
+    <tr><td>NAND</td><td>Yes</td><td></td></tr>
+    <tr><td>P2WI/RSB</td><td>Yes</td><td></td></tr>
+    <tr><td>PCIe</td><td>-</td><td></td></tr>
+    <tr><td>PWM</td><td>Yes</td><td></td></tr>
+    <tr><td>RTC</td><td>Yes</td><td></td></tr>
+    <tr><td>SATA</td><td>Yes</td><td></td></tr>
+    <tr><td>SD/MMC</td><td>Yes</td><td></td></tr>
+    <tr><td>SMP</td><td>Yes</td><td></td></tr>
+    <tr><td>SPDIF</td><td>-</td><td></td></tr>
+    <tr><td>SPI</td><td>Yes</td><td></td></tr>
+    <tr><td>Thermal sensors</td><td>Yes</td><td></td></tr>
+    <tr><td>UART</td><td>Yes</td><td></td></tr>
+    <tr><td>USB 2.0</td><td>Yes</td><td></td></tr>
+    <tr><td>USB 3.0</td><td>Yes</td><td></td></tr>
+    <tr><td>Watchdog timer</td><td>Yes</td><td></td></tr>
+  </tbody>
+</table>
+
+# Installation
+
+- Download or build **arm64.img** (64-bit) from NetBSD 9.0 or later
+- Write the image to disk: **dd if=arm64.img of=/dev/rld0d bs=1m conv=sync**
+- Install a board-specific U-Boot from pkgsrc to the SD card
+  **dd if=/usr/pkg/share/u-boot/&lt;boardname&gt;/rkspi_loader.img of=/dev/rld0d seek=64 conv=sync**
+
+If your SoC has a SATA controller and you would like to install on
+an hard disk and use a SD card only for u-boot please give a look
+to
+[[NetBSD/evbarm install via sysinst(8) on a SATA hard disk, USB stick or (u)SD card|ports/evbarm/install_using_sysinst]].
+
+# Tips and tricks
+
+# Links
+
+- [[NetBSD/evbarm install via sysinst(8) on a SATA hard disk, USB stick or (u)SD card|ports/evbarm/install_using_sysinst]]