Annotation of wikisrc/ports/evbarm/raspberry_pi.mdwn, revision 1.71

1.1       jakllsch    1: [[!meta title="NetBSD/evbarm on Raspberry Pi"]]
                      2: 
1.39      wiki        3: This page attempts to document and coordinate efforts towards NetBSD/evbarm on [Raspberry Pi](http://www.raspberrypi.org). All board variants are supported.
                      4: 
1.70      gdt         5: Initial, limited, Raspberry Pi support was introduced in NetBSD 6.0. NetBSD 7.0 adds complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.  Raspberry Pi 3 support was added for NetBSD 8, and backported to NetBSD 7 in July of 2017.  (This page assumes those using NetBSD 7 are using 7.2, or the netbsd-7 branch after mid 2018.)
1.39      wiki        6: 
1.3       wiki        7: [[images/raspberrypi.jpg]]
                      8: 
1.26      wiki        9: [[!toc levels=2]]
                     10: 
1.14      wiki       11: <small>([Raspberry Pi image](http://www.flickr.com/photos/42325803@N07/8118758647/) by Christopher Lee used under CC-By-2.0 license)</small>
1.3       wiki       12: 
1.54      gdt        13: # What works (and what doesn't yet)
1.53      gdt        14: 
1.70      gdt        15: ## NetBSD 7 and NetBSD 8
1.53      gdt        16: 
                     17:  - RaspberryPi 1, and 2 (including SMP)
1.70      gdt        18:  - Raspberry Pi 3 (excluding WiFi and bluetooth)
1.53      gdt        19:  - multi-user boot with root on SD card
                     20:  - serial or graphics console (with EDID query / parsing)
                     21:  - DMA controller driver and sdhc(4) support
                     22:  - Audio: works. man page missing.
                     23:  - I²C: works, could use enhancements, man page
                     24:  - GPIO
                     25:  - RNG
                     26:  - SPI: could use enhancements, man page
                     27:  - GPU (VCHIQ) - 3D and video decode. man page missing.
                     28:  - USB (host) - dwctwo(4)
                     29:  - USB Ethernet - usmsc(4)
                     30:  - X windows.
                     31: 
                     32: ## NetBSD current
                     33: 
                     34:  - Raspberry Pi 3 bluetooth
                     35:  - Raspberry Pi 3 new SD host controller driver
                     36: 
1.54      gdt        37: ## What needs work
1.53      gdt        38: 
                     39:  - USB (host); isochronous transfers.
                     40:  - WiFi
                     41: 
1.57      gdt        42: # CPU types
                     43: 
                     44: Note that one can also use code for earlier models on later models.
                     45: 
1.59      gdt        46:  - Raspberry Pi 1 uses "earmv6hf".
                     47:  - Raspberry Pi 2 uses "earmv7hf".
1.64      gdt        48:  - Raspberry Pi 3 uses "earmv7hf".
1.57      gdt        49: 
1.70      gdt        50: See also [[NetBSD/aarch64|aarch64]] for running the Pi 2/3 in 64-bit mode.
                     51: 
1.7       wiki       52: # Installation
1.53      gdt        53: 
1.62      gdt        54: ## SD card structure
                     55: 
1.65      gdt        56: The Raspberry Pi looks for firmware and kernel.img on the first FAT32 partition of the uSD card.  A separate kernel (kernel7.img) is used on RPI2 and RPI3.
1.62      gdt        57: 
1.65      gdt        58: The NetBSD kernel will then use the FFS partition as the root filesystem.
                     59: 
                     60: A 2 GB card is the smallest workable size.  The NetBSD filesystem will be expanded to fit.
1.63      gdt        61: 
1.62      gdt        62: ## Choosing a version
                     63: 
1.71    ! gdt        64: First, decide if you want to install a formal release (7.2 or 8.0), a stable branch build (netbsd-7, netbsd-8), or NetBSD-current.  For people who don't know how to choose among those, 8.0 or netbsd-8 is probably best.
1.65      gdt        65: 
                     66: See also "ebijun's image", below, which is NetBSD-current and includes packages.
1.58      gdt        67: 
                     68: ## Getting bits to install
                     69: 
                     70: You can either build a release yourself with build.sh, or get one from the NetBSD FTP servers.
                     71: 
1.65      gdt        72: Both will provide rpi.img.gz and rpi_inst.img.gz.  Each is an image to be written to a uSD card, and has a FAT32 partition for booting.  In rpi.img.gz, there is also an FFS partition for NetBSD.
1.58      gdt        73: 
                     74: ### Building yourself
                     75: 
1.65      gdt        76: Getting sources and building a release with build.sh is not special for evbarm.  Pick a CPU type alias and pass it to build.sh with -m.  Examples (the first two are equivalent):
1.66      gdt        77: 
1.59      gdt        78:  - ./build.sh -m earmv6hf -u release
                     79:  - ./build.sh -m evbarm -a earmv6hf -u release
                     80:  - ./build.sh -m evbarm -a earmv7hf -u release
1.58      gdt        81: 
                     82: ### NetBSD FTP servers
                     83: 
                     84: NetBSD provides nightly builds on [nyftp.netbsd.org](http://nyftp.netbsd.org/pub/NetBSD-daily/).  These are equivalent to building yourself.
                     85: 
1.59      gdt        86:  - The 'evbarm-earmv6hf/binary/gzimg/' directory contains an rpi.img file that can be used as a single image for both boards.
1.71    ! gdt        87:  - The 'evbarm-earmv7hf/binary/gzimg/' directory contains an armv7.img file that is optimized for Raspberry Pi 2/3.
        !            88:  - The old stable build directory will be under netbsd-7/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-7/201710201440Z/evbarm-earmv6hf/binary/gzimg)    
        !            89:  - The stable build directory will be under netbsd-8/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-8/201710211010Z/evbarm-earmv6hf/binary/gzimg/)
1.59      gdt        90:  - The HEAD/current directory build will be under HEAD/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/HEAD/201710202210Z/evbarm-earmv7hf/binary/gzimg/)
1.58      gdt        91: 
1.65      gdt        92: ## Preparing a uSD card
1.10      wiki       93: 
1.65      gdt        94: Once you have rpi.img.gz (or rpi_inst), put it on a uSD card using gunzip and dd, for example:
1.14      wiki       95: 
1.60      gdt        96:  - gunzip rpi.img.gz
1.67      ryoon      97:  - dd if=rpi.img of=/dev/disk1
1.14      wiki       98: 
1.58      gdt        99: ### Serial Console
                    100: 
                    101: By default the rpi.img is set to use the HDMI output.  If you wish to use a serial console, first mount the FAT32 partition and then
                    102: edit cmdline.txt and remove '"console=fb"'.
1.14      wiki      103: 
1.60      gdt       104:  - Most (all?) USB-to-TTL serial adapters only connect Tx, Rx and ground, and do not connect any flow control lines. An effect of missing flow control is that you see console output, but cannot type anything. If so, adjust your serial console application's flow control settings to "none".
1.41      wiki      105: 
1.60      gdt       106:    In Kermit, the command is "set flow none".
1.41      wiki      107: 
1.60      gdt       108:    In minicom, run "minicom -s" and set hardware flow control to "no"
1.41      wiki      109: 
1.65      gdt       110: ### Enabling ssh
                    111: 
                    112: If you want to enable ssh with the standard image, so that you can log in over the net without either a serial or HDMI console, mount the ffs partition, place /root/.ssh/authorized_keys, uncomment PermitRootLogin in /etc/ssh/sshd_config, and comment out the rc_configure=NO in /etc/rc.conf.  Besides having to find the IP address, you will have to wait for the partition resizing and reboot.
                    113: 
1.58      gdt       114: ### Installation with sshramdisk image
                    115: 
1.65      gdt       116: build.sh (and hence the FTP site) also creates an image 'rpi_inst.img.gz' specifically for installation without HDMI or a serial console.  Note that this image is much smaller and that you will need to fetch the sets over the network.  To use this method, write that image to a uSD card as above, and then:
1.53      gdt       117: 
1.61      gdt       118:  - Ensure that you have a lan with a DHCP server.
                    119:  - Connect an Ethernet cable from the RPI to the LAN.
1.19      wiki      120:  - After starting DHCP client, SSH login to with user "sysinst", and password "netbsd".
1.17      wiki      121:    - Be careful to note the ip address given during DHCP so you don't lose your connection
                    122:    - Also for after the sysinst is done and the system reboots
                    123:  - sysinst started!
1.16      wiki      124: 
1.55      gdt       125: ## Installation via ebijun's image
                    126: 
1.58      gdt       127: As an alternative to the standard installation images, Jun Ebihara
                    128: provides an install image for Raspberry Pi that includes packages.  It
                    129: is based on NetBSD-current and is built for earmv6hf, and thus will
                    130: work on Raspberry Pi 1, 2 and 3.  This image is typically updated
                    131: every few weeks.
1.55      gdt       132: 
1.56      gdt       133:  - [https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README](https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README)
1.55      gdt       134: 
1.53      gdt       135: ## Updating the kernel
1.46      schmonz   136: 
1.42      wiki      137:  - Build a new kernel, e.g. using build.sh. It will tell you where the ELF version of the kernel is, e.g.
                    138: 
                    139:          ...
                    140:          Kernels built from RPI2:
                    141:           /Users/feyrer/work/NetBSD/cvs/src-current/obj.evbarm-Darwin-XXX/sys/arch/evbarm/compile/RPI2/netbsd
                    142:          ...
                    143: 
1.69      rin       144:  - Besides the "netbsd" kernel in ELF format, there is also a "netbsd.img" (for current) or "netbsd.bin" (for 7 and 8) kernel that is in a format that the Raspberry can boot.
1.48      sevan     145:  - Depending on your hardware version, copy this either to /boot/kernel.img (First generation Pi, Pi Zero hardware) or to /boot/kernel7.img (Pi 2, Pi 3 hardware)
1.42      wiki      146:  - reboot
                    147: 
1.24      wiki      148: # Wireless Networking
1.53      gdt       149: 
                    150:   Note that the built-in WiFi in the RPI3 is not yet supported.
                    151: 
1.24      wiki      152:  - A Realtek 802.11n USB adaptor configures as urtwn(4).
1.25      wiki      153:    - Configure with wpa_supplicant in /etc/rc.conf -
1.24      wiki      154: 
                    155:            ifconfig_urtwn0=dhcp
                    156:            dhcpcd=YES
                    157:            dhcpcd_flags="-q -b"
                    158:            wpa_supplicant=YES
                    159:            wpa_supplicant_flags="-B -i urtwn0 -c /etc/wpa_supplicant.conf"
1.25      wiki      160:    - A sample wpa_supplicant.conf can be found at /usr/share/examples/wpa_supplicant/wpa_supplicant.conf
1.24      wiki      161: 
1.27      wiki      162: # GPU
                    163: 
                    164: ## Video playback
1.29      wiki      165: Accelerated video playback is supported in NetBSD 7 with the [OMXPlayer](http://pkgsrc.se/multimedia/omxplayer) application and through GStreamer with the [omx](http://pkgsrc.se/multimedia/gst-plugins1-omx) plugin.
1.27      wiki      166: 
                    167: ## OpenGL ES
                    168: Accelerated OpenGL ES is supported in NetBSD 7. The GL ES client libraries are included with the [misc/raspberrypi-userland](http://pkgsrc.se/misc/raspberrypi-userland) package.
                    169: 
1.28      wiki      170: ## Quake 3
1.27      wiki      171: A Raspberry Pi optimized build of *ioquake3* is available in the [games/ioquake3-raspberrypi](http://pkgsrc.se/games/ioquake3-raspberrypi) package. To use it, the following additional resources are required:
                    172: 
                    173:  - pak0.pk3 from Quake 3 CD
1.31      snj       174:  - additional pak files from the [games/ioquake3-pk3](http://pkgsrc.se/games/ioquake3-pk3) package
1.27      wiki      175:  - read/write permissions on /dev/vchiq and /dev/wsmouse
                    176: 
1.31      snj       177: Place the pak0.pk3 file in the /usr/pkg/lib/ioquake3/baseq3 directory.
1.27      wiki      178: 
1.32      wiki      179: ## RetroArch / Libretro
                    180: Using [emulators/retroarch](http://pkgsrc.se/emulators/retroarch) it is possible to run many emulators at full speed the Raspberry Pi. Emulator cores for various gaming consoles are available in the [emulators/libretro-*](http://pkgsrc.se/search.php?so=libretro-) packages. To begin using retroarch:
                    181: 
                    182:  - Install [emulators/retroarch](http://pkgsrc.se/emulators/retroarch)
                    183:  - Install the libretro core for the system you would like to emulate (lets take [emulators/libretro-gambatte](http://pkgsrc.se/emulators/libretro-gambatte), a GameBoy Color emulator, as an example).
                    184:  - Plug in a USB HID compatible Gamepad, such as the Logitech F710 in "DirectInput" mode (set "D/X" switch to "D").
                    185:  - Create a config file for your gamepad using *retroarch-joyconfig*.
                    186: [[!template  id=programlisting text="""
1.35      wiki      187: $ retroarch-joyconfig -o gamepad.cfg
1.32      wiki      188: """]]
                    189:  - Launch the emulator from the command-line (no X required):
                    190: [[!template  id=programlisting text="""
                    191: $ retroarch --appendconfig gamepad.cfg -L /usr/pkg/lib/libretro/gambatte_libretro.so game.gbc
                    192: """]]
                    193: 
1.53      gdt       194: # Developer notes
1.50      gdt       195: 
1.53      gdt       196: These notes are for people working on improvements to RPI support in NetBSD.
1.50      gdt       197: 
1.53      gdt       198: ## Updating the firmware
1.50      gdt       199: 
1.53      gdt       200: You probably don't want to do this. Firmware updates can break things,
                    201: and the latest firmware that's been tested is already included in the
                    202: NetBSD build you installed.
1.50      gdt       203: 
1.53      gdt       204: If you're feeling adventurous (or are the port maintainer), here's what
                    205: to test whenever you try new firmware:
1.50      gdt       206: 
1.53      gdt       207: - Audio
                    208: - OMXPlayer (and [[!template id=man name="vchiq"]])
                    209: - Serial/framebuffer console
                    210: - CPU frequency scaling
1.50      gdt       211: 
1.53      gdt       212: That goes for all of `rpi[0123]`.
1.1       jakllsch  213: 
1.53      gdt       214: Upstream firmware releases are
                    215: [on GitHub](https://github.com/raspberrypi/firmware/releases).
                    216: Copy all files except `kernel*.img` into `/boot` and reboot.

CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb