Annotation of wikisrc/ports/evbarm/raspberry_pi.mdwn, revision 1.125

1.1       jakllsch    1: [[!meta title="NetBSD/evbarm on Raspberry Pi"]]
1.120     gdt         3: This page describes the NetBSD/evbarm port on [Raspberry Pi]( hardware.  All [board variants]( earlier than the RPI4 are believed supported, and specific boards known to work are listed.  We use e.g. "RPI2" to refer to "Raspberry Pi 2" to save precious bytes on this page.  This web page is 32-bit (aarch32) centric, as that has been until mid-2018 the only approach.
1.39      wiki        4: 
1.104     gdt         5: Initial, limited, Raspberry Pi support was introduced in NetBSD 6.0.  NetBSD 7.0 adds complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.  Raspberry Pi 3 support was added for NetBSD 8, and backported to NetBSD 7 in July of 2017.  (This page assumes those using NetBSD 7 are using 7.2 or later, but note that everyone uses 8 or -current.)
1.39      wiki        6: 
1.120     gdt         7: In mid-2018, -current gained support for 64-bit ARM (aarch64) support.  This will be in NetBSD 9.
1.114     gdt         8: 
1.3       wiki        9: [[images/raspberrypi.jpg]]
1.26      wiki       11: [[!toc levels=2]]
1.14      wiki       13: <small>([Raspberry Pi image]( by Christopher Lee used under CC-By-2.0 license)</small>
1.3       wiki       14: 
1.54      gdt        15: # What works (and what doesn't yet)
1.53      gdt        16: 
1.123     gdt        17: "Works" is primarily relative to the earmv6hf-el and earmv7hf-el CPU targets (32-bit).
1.70      gdt        19: ## NetBSD 7 and NetBSD 8
1.53      gdt        20: 
1.102     gdt        21:  - RPI1, RPI2, RPI2-1.2, RPI3, RPI3+ (except RPI3 builtin WiFi and bluetooth)
                     22:  - RPI0 and RPI0W are expected to work (without WiFi, and one needs fdt files \todo where from?)
1.101     gdt        23:  - multiple processors on RPI2/RPI3
1.74      gdt        24:  - boots normally to multiuser, with FAT32 boot partition on uSD
                     25:  - root filesystem can be uSD or USB-attached mass storage
1.53      gdt        26:  - serial or graphics console (with EDID query / parsing)
1.74      gdt        27:  - X11 via HDMI
                     28:  - GPU (VCHIQ) - 3D and video decode. man page missing.
                     29:  - USB host controller - dwctwo(4) and most devices work
                     30:  - USB Ethernet - usmsc(4)
1.53      gdt        31:  - DMA controller driver and sdhc(4) support
1.74      gdt        32:  - RNG
1.53      gdt        33:  - Audio: works. man page missing.
1.74      gdt        34:  - GPIO
1.53      gdt        35:  - I²C: works, could use enhancements, man page
                     36:  - SPI: could use enhancements, man page
1.123     gdt        38: ## NetBSD 9
                     40:  - aarch64 support (RPI3, and should work on all supported systems with 64-bit CPUs)
1.125   ! gdt        42: ## NetBSD current
1.53      gdt        43: 
1.101     gdt        44:  - RPI3 builtin bluetooth
                     45:  - RPI3 new SD host controller driver
1.53      gdt        46: 
1.125   ! gdt        47: ## (maybe) NetBSD current, with manual steps
        !            48: 
        !            49:    These items do not work in the sense that they simply function after a standard install.  Being listed here implies only that there has been list traffic that implies that after taking a bunch of steps (e.g. new firmware, new dtbs, enabling drivers, applying patches), one can end up with the feature working.  The HOWTO explicitly refrains from describing these steps because they are ephemeral.  However, the fact that list traffic indicates success is possible is a clue that proper support is on the horizon, and that is notable.
        !            50: 
        !            51:  - RPI3, RPI0W builtin WiFi
        !            52: 
1.102     gdt        53: ## What needs documenting if it works
                     55:  - CM1
                     56:  - CM3
                     57:  - CM3lite
1.54      gdt        59: ## What needs work
1.53      gdt        60: 
1.122     gdt        61:  - RPI4 (as of 2020-01, still does not work in current)
1.53      gdt        62:  - USB (host); isochronous transfers.
1.105     gdt        63:  - RPI0W Bluetooth Low Energy (probably)
1.53      gdt        64: 
1.57      gdt        65: # CPU types
1.101     gdt        67:  - RPI1 uses "earmv6hf".
1.109     gdt        68:  - RPI0 uses "earmv6hf".
                     69:  - RPI0W uses "earmv6hf".
1.101     gdt        70:  - RPI2 uses "earmv7hf".
1.113     gdt        71:  - RPI2-1.2 uses "earmv7hf" or "aarch64" (armv8 CPU hardware)
                     72:  - RPI3 uses "earmv7hf" or "aarch64" (armv8 CPU hardware)
1.57      gdt        73: 
1.101     gdt        74: Note that one can run a build of earmv6hf on the 2 and 3.  There will still be a kernel7, built to use the 2/3 hardware, but with the armv6 instruction set.
1.96      gdt        75: 
1.101     gdt        76: In theory the code compiled for earmv7hf will be faster, but anecdotal experience is that it doesn't matter that much.
1.97      gdt        77: 
1.101     gdt        78: While the evbarm port has "eb" variants (for big-endian mode), the RPI systems do not support eb and these variants will not work.  Systems built with older CPU architectures (earm, earmv4, earmv5) are not expected to work on RPI.
1.96      gdt        79: 
1.113     gdt        80: The RPI2-1.2 and RPI3 have an armv8 CPU that supports aarch64 (64-bit
                     81: mode) in addition to aarch32 (regular 32-bit ARM).  This is supported,
1.123     gdt        82: from -9 onwards, by the "aarch64" MACHINE_ARCH of evbarm, also
                     83: available in via the alias evbarm64.  This is also
1.113     gdt        84: referred to as [[NetBSD/aarch64|aarch64]].
1.70      gdt        85: 
1.7       wiki       86: # Installation
1.53      gdt        87: 
1.62      gdt        88: ## SD card structure
1.86      gdt        90: The Raspberry Pi looks for firmware and kernel.img on the first FAT32 MBR partition of the uSD card.  A separate kernel (kernel7.img) is used on RPI2 and RPI3.
                     91: The NetBSD kernel will then find NetBSD MBR partition and within that the root disklabel partition, and use that FFS partition as the root filesystem.
1.62      gdt        92: 
1.86      gdt        93: A 2 GB card is the smallest workable size, and the installation image will fit.  After the first boot, the system resizes the NetBSD root partition to fill the card.  Note that swap is after /boot and before /, and not contained in the NetBSD fdisk partition.  However, if you don't try to change the partition structure, this should not cause you any trouble.
1.63      gdt        94: 
1.91      gdt        95: Note that SD cards generally have limited write tolerance, so you may wish to disable atime updates via the noatime option, as is done by the default installation.
1.62      gdt        97: ## Choosing a version
1.95      gdt        99: First, decide if you want to install a formal release (7.2 or 8.0), a stable branch build (netbsd-7, netbsd-8), or NetBSD-current.  For people who don't know how to choose among those, a recent build of netbsd-8 is probably best, with 8.0 the choice for those who value being at exactly a formal release.
1.65      gdt       100: 
                    101: See also "ebijun's image", below, which is NetBSD-current and includes packages.
1.58      gdt       102: 
                    103: ## Getting bits to install
1.96      gdt       105: You can either build a release yourself with, or get a release from the NetBSD HTTPS/FTP servers.  The bits from both sources should match, except for things like  timestamps, or because the sources are from slightly different points along branches.
1.58      gdt       106: 
                    107: ### Building yourself
1.95      gdt       109: Getting sources and building a release with is not special for evbarm.  However, the evbarm port has a very large number of CPU types, compared to i386 and amd64 which have one each.  The standard approach is to use -m to define MACHINE and -a to define MACHINE_ARCH. supports aliases that can be passed as a MACHINE value, but denote both MACHINE and a MACHINE_ARCH.   The third line uses an alias and is equal to the second, for RPI2/3.  Note that the aliases start with "evb" while the MACHINE_ARCH values do not, and that aliases have "-el" or "-eb", while the MACHINE_ARCH values have no suffix or "eb".
1.66      gdt       110: 
1.59      gdt       111:  - ./ -m evbarm -a earmv6hf -u release
                    112:  - ./ -m evbarm -a earmv7hf -u release
1.95      gdt       113:  - ./ -m evbearmv7hf-el -u release
1.81      gdt       114: 
1.94      gdt       115: Consider setting RELEASEMACHINEDIR if you wish to build multiple MACHINE_ARCH values for a MACHINE; see  Use something like "evbarm-earmv7hf", so that 1) earvm6 and earmv7 don't collide and 2) anita will recognize it as a type of evbarm.
1.58      gdt       116: 
1.85      gdt       117: ### NetBSD autobuild HTTPS/FTP servers
1.58      gdt       118: 
1.115     sevan     119: NetBSD provides nightly builds on [](  The next directory level is the branch being built (netbsd-7, netbsd-8, HEAD, and more), plus optionally things like compiler type.  It is followed by date/time, e.g. "HEAD/201811051650Z"; once a build is complete the symlink "latest" is adjusted to point to it.  The next level is "${MACHINE}-${MACHINE_ARCH}", e.g. "evbarm-earmv7hf", and multiple combinations are provided.
1.58      gdt       120: 
1.115     sevan     121: An example URL, arguably the standard approach for first-time NetBSD/RPI users, is
1.95      gdt       122: 
                    123: ### release layout
1.96      gdt       125: Once you get to the releasedir, self-built and autobuild releases have the same structure.
1.85      gdt       127:  - The 'evbarm-earmv6hf/binary/gzimg/' directory contains an rpi.img file that will run on any of the RPI boards.
1.103     gdt       128:  - The 'evbarm-earmv7hf/binary/gzimg/' directory contains an armv7.img file that uses the armv7 instruction set, and thus can run only on the RPI2 and RPI3 (and perhaps the CM3).  It also supports systems other than the RPI family.
1.85      gdt       129: 
1.95      gdt       130: \todo Explain why there is no armv7_inst.gz.
1.58      gdt       131: 
1.65      gdt       132: ## Preparing a uSD card
1.10      wiki      133: 
1.107     gdt       134: Once you have rpi.img.gz (or rpi_inst for earmv6 boards), put it on a uSD card using gunzip and dd, for example:
1.14      wiki      135: 
1.60      gdt       136:  - gunzip rpi.img.gz
1.67      ryoon     137:  - dd if=rpi.img of=/dev/disk1
1.14      wiki      138: 
1.89      gdt       139: ## Console approaches
                    141: The standard approach is to use a USB keyboard and an HDMI monitor for installation.
1.58      gdt       143: ### Serial Console
1.89      gdt       145: By default the rpi.img is set to use the HDMI output.  If you wish to use a serial console, mount the FAT32 partition on another system and edit cmdline.txt and remove '"console=fb"'.
1.14      wiki      146: 
1.109     gdt       147:  - Most (all?) USB-to-TTL serial adapters have wires for TX, RX and ground, and not RTS/CTS or other flow control lines.   Thus, your terminal program (or terminal) must be configured to not require flow control; a symptom of misconfiguration is that you see console output, but cannot type anything.  If so, adjust your serial console application's flow control settings to "none".
1.41      wiki      148: 
1.89      gdt       149:    - In Kermit, the command is "set flow none".
                    150:    - In minicom, run "minicom -s" and set hardware flow control to "no".
1.41      wiki      151: 
1.89      gdt       152: ### Enabling ssh for installation without any console
1.41      wiki      153: 
1.89      gdt       154: If you want to enable ssh with the standard image, so that you can log in over the net without either a serial or HDMI console, you can edit the configuration of a uSD card before booting.   On another computer, mount the ffs partition, place /root/.ssh/authorized_keys, uncomment PermitRootLogin in /etc/ssh/sshd_config, and comment out the rc_configure=NO in /etc/rc.conf.  Besides having to find the IP address (e.g. from DHCP server logs), you will have to wait for the partition resizing and reboot.
1.65      gdt       155: 
1.89      gdt       156: ### Installation with sshramdisk image
1.65      gdt       157: 
1.89      gdt       158: (and hence the FTP site) also creates an image 'rpi_inst.img.gz' specifically for installation without HDMI or a serial console, when built for earmv6hf.  Note that this image is much smaller and that you will need to fetch the sets over the network.  To use this method, write that image to a uSD card as above, and then:
1.58      gdt       159: 
1.89      gdt       160:  - Connect an Ethernet cable from the RPI to a LAN with a DHCP server, and another host you can use for ssh.
                    161:  - Power on the RPI, and wait.  Watch the logs on the DHCP server, and find the IP address assigned to the RPI.
                    162:  - Use ssh to login to the address you found with user "sysinst", and password "netbsd".
                    163:  - When installing, ensure that you enable DHCP and ssh, so that you can log in again after the system is installed.
1.53      gdt       164: 
1.107     gdt       165: The rpi_inst.img.gz image will only work for systems that use earmv6hf kernels (so not RPI2/3).  See [this port-arm message]( for details.
1.55      gdt       167: ## Installation via ebijun's image
1.58      gdt       169: As an alternative to the standard installation images, Jun Ebihara
                    170: provides an install image for Raspberry Pi that includes packages.  It
                    171: is based on NetBSD-current and is built for earmv6hf, and thus will
                    172: work on Raspberry Pi 1, 2 and 3.  This image is typically updated
                    173: every few weeks.
1.55      gdt       174: 
1.121     cnst      175:  - <>
1.55      gdt       176: 
1.98      gdt       177: ## Configuring 802.11
                    179: After installation, the Ethernet will function as on any other NetBSD system; simply enable dhcpcd or configure a static address.  USB WiFi devices will also function as on any other NetBSD system; in addition to dhcpcd or static, configure and enable wpa_supplicant.
                    181: Note that the built-in WiFi in the RPI3 is not yet supported.   USB WiFi interfaces (that work on NetBSD in general) should all work.  In particular, the following are known to work:
                    183:  - urtwn0: Realtek (0xbda) 802.11n WLAN Adapter (0x8176), rev 2.00/2.00, addr 5, MAC/BB RTL8188CUS, RF 6052 1T1R
1.90      gdt       185: ## Links
                    187: The following pages have been published by NetBSD community members.  (Note that some of them are old.)
                    189:  -
1.74      gdt       191: # Maintaining a system
1.78      gdt       193: ## vcgencmd
1.80      gdt       195: The program vcgencmd, referenced in the boot section,  can be found in pkgsrc/misc/raspberrypi-userland.
1.78      gdt       196: 
1.53      gdt       197: ## Updating the kernel
1.46      schmonz   198: 
1.42      wiki      199:  - Build a new kernel, e.g. using It will tell you where the ELF version of the kernel is, e.g.
                    201:          ...
                    202:          Kernels built from RPI2:
                    203:           /Users/feyrer/work/NetBSD/cvs/src-current/obj.evbarm-Darwin-XXX/sys/arch/evbarm/compile/RPI2/netbsd
                    204:          ...
1.69      rin       206:  - Besides the "netbsd" kernel in ELF format, there is also a "netbsd.img" (for current) or "netbsd.bin" (for 7 and 8) kernel that is in a format that the Raspberry can boot.
1.48      sevan     207:  - Depending on your hardware version, copy this either to /boot/kernel.img (First generation Pi, Pi Zero hardware) or to /boot/kernel7.img (Pi 2, Pi 3 hardware)
1.42      wiki      208:  - reboot
1.73      gdt       210: ## Updating the firmware
                    212: A section below describes the process of updating NetBSD's copy of the firmware from upstream, with testing, by NetBSD developers.  This section is about updating a system's firmware from the firmware in a version of NetBSD.
1.88      gdt       214: \todo Explain where the firmware is in the source tree, and if it is in the installed system image (such as /usr/mdec).  Explain how to update a system (presumably /boot) from either an installed system's new firmware files, or the source tree.  Explain any particular cautions.
1.73      gdt       215: 
1.105     gdt       216: Probably, for the RPI3+, one needs to use -current, or use -8 with firmware from -current.  \todo Defuzz.
1.101     gdt       217: 
1.99      gdt       218: \todo Explain if using updated firmware from one branch (e.g. netbsd-current) on a system using a different branch (e.g. netbsd-8) is safe.  Explain if pullups are done to release branches with new firmware.
1.75      gdt       220: ## Booting
1.79      gdt       222: The device boots by finding a file "bootcode.bin".   The primary location is a FAT32 partition on the uSD card, and an additional location is on a USB drive.  See the [upstream documentation on booting]( and read all the subpages.
1.75      gdt       223: 
1.112     gdt       224: The standard approach is to use a uSD card, with a fdisk partition table containing a FAT32 partition marked active, and a NetBSD partition.  The NetBSD partition will then contain a disklabel, pointing to an FFS partition (a), a swap partition (b) and the FAT32 boot partition mounted as /boot (e).  The file /boot/cmdline.txt has a line to set the root partition.
1.75      gdt       225: 
1.112     gdt       226: One wrinkle in the standard approach is that the disk layout is "boot swap /", but the NetBSD fdisk partition starts at the location of /, so the swap partition is not within the NetBSD fdisk partition.  The / partition can hold a disklabel, while swap cannot.   It is normal to have swap after / (and thus within the fdisk partition), but the arrangement used permits growing / on first boot, for the typical case where a larger uSD is used, compared to the minimum image size.
1.75      gdt       227: 
1.77      gdt       228: An alternate approach is to have the boot FAT32 partition as above, but to have the entire system including root on an external disk.  This is configured by changing root=ld0a to root=sd0a or root=dk0 (depending on disklabel/GPT).  Besides greater space, part of the point is to avoid writing to the uSD card.
1.75      gdt       229: 
1.80      gdt       230: A third approach, workable on the Pi 3 only, is to configure USB host booting (already enableed on the 3+; see the upstream documentation) and have the boot partition also on the external device.  In this case the external device must have an MBR because the hardware's first-stage boot does not have GPT support. In theory the [procedure to program USB host boot mode]( will function on a NetBSD system because the programming is done by bootcode.bin.
                    231: \todo Confirm that putting program_usb_boot_mode=1 in config.txt and booting works to program the OTP bit.  Confirm that one can then boot NetBSD from external USB.
1.75      gdt       232: 
1.101     gdt       233: There is no well-defined USB enumeration order, so the preferred approach if one has multiple USB mass storage devices is to use named wedges in both fstab and cmdline.txt.
1.75      gdt       234: 
1.113     gdt       235: ## Split-mode aarch32/aarch64
                    237: \todo Verify this, and add any necessary cautions about boot code.
                    239: The aarch64 kernel can run aarch32 binaries, so one can boot a aarch64 kernel on a system with aarch32 userland.
1.93      gdt       241: # X11 and GPU
1.27      wiki      243: ## Video playback
1.29      wiki      244: Accelerated video playback is supported in NetBSD 7 with the [OMXPlayer]( application and through GStreamer with the [omx]( plugin.
1.27      wiki      245: 
                    246: ## OpenGL ES
                    247: Accelerated OpenGL ES is supported in NetBSD 7. The GL ES client libraries are included with the [misc/raspberrypi-userland]( package.
1.28      wiki      249: ## Quake 3
1.27      wiki      250: A Raspberry Pi optimized build of *ioquake3* is available in the [games/ioquake3-raspberrypi]( package. To use it, the following additional resources are required:
                    252:  - pak0.pk3 from Quake 3 CD
1.31      snj       253:  - additional pak files from the [games/ioquake3-pk3]( package
1.27      wiki      254:  - read/write permissions on /dev/vchiq and /dev/wsmouse
1.31      snj       256: Place the pak0.pk3 file in the /usr/pkg/lib/ioquake3/baseq3 directory.
1.27      wiki      257: 
1.32      wiki      258: ## RetroArch / Libretro
                    259: Using [emulators/retroarch]( it is possible to run many emulators at full speed the Raspberry Pi. Emulator cores for various gaming consoles are available in the [emulators/libretro-*]( packages. To begin using retroarch:
                    261:  - Install [emulators/retroarch](
                    262:  - Install the libretro core for the system you would like to emulate (lets take [emulators/libretro-gambatte](, a GameBoy Color emulator, as an example).
1.118     nia       263:  - Make sure your user has read and write permissions on `/dev/vchiq`.
                    264:  - Plug in a USB HID compatible Gamepad, such as the Logitech F710 in "DirectInput" mode (set "D/X" switch to "D"). Note that since the framebuffer GL driver will not allow for keyboard input in RetroArch, you will have to copy your joypad configuration from another system.
                    265:  - Configure retroarch by editing $HOME/.config/retroarch/retroarch.cfg:
                    266:        video_driver = "gl"
                    267:        input_driver = "null"
                    268:        joypad_driver = "sdl2"
1.116     nia       269:        menu_driver = "rgui"
1.32      wiki      270: 
1.53      gdt       271: # Developer notes
1.50      gdt       272: 
1.53      gdt       273: These notes are for people working on improvements to RPI support in NetBSD.
1.50      gdt       274: 
1.72      gdt       275: ## Updating the firmware version in the NetBSD sources
1.50      gdt       276: 
1.72      gdt       277: (Note that trying new firmware may result in a non-bootable system, so
                    278: be prepared to recover the bootable media with another system.)
1.50      gdt       279: 
1.72      gdt       280: Upstream firmware releases are
                    281: [on GitHub](
                    282: Copy all files except `kernel*.img` into `/boot` and reboot.
                    284: New firmware should pass all of the following tests before being committed to NetBSD.
1.50      gdt       285: 
1.53      gdt       286: - Audio
                    287: - OMXPlayer (and [[!template id=man name="vchiq"]])
                    288: - Serial/framebuffer console
                    289: - CPU frequency scaling
1.50      gdt       290: 
1.92      gdt       291: Tests should be run on all of `rpi[0123]`.
1.94      gdt       292: 
                    293: ## Testing with anita and qemu
1.111     gdt       295: See the anita section in the evbarm page.
1.94      gdt       296: 
1.110     gdt       297: It is not currently known how to emulate a RPI in qemu, and therefore anita does not yet have support for this.  \todo Add a command-line example to run qemu emulating some RPI model.
1.119     leot      298: 
                    300: # Misc notes
                    301: Miscellaneous notes about Raspberry PI.
                    303: ## Power supply needed (or: why there is a little rainbow square in the top-right corner?)
                    304: Raspberry Pi devices are powered by 5V micro USB and a 2.5A (2500mA)
1.124     gdt       305: power supply is recommended.  For more information please read:
1.119     leot      306: 
                    307:  <>
                    309: Power glitches can also manifest in other ways, e.g. with an USB
                    310: disk plugged:
                    312: [[!template id=programlisting text="""
                    313: sd0(umass0:0:0:0): generic HBA error
                    314: sd0: cache synchronization failed
                    315: """]]
1.124     gdt       317: Using a recommended power supply avoid such issues.
1.119     leot      318: 
                    319: ## Xenon death flash (Raspberry Pi 2 is camera-shy)
                    320: When using laser pointers or xenon flashes in cameras (or other
                    321: flashes of high-intensity long-wave light) against a Raspberry Pi
                    322: 2 the Pi can power itself off.
                    323: For more information please read:
                    325:  <>

CVSweb for NetBSD wikisrc <> software: FreeBSD-CVSweb