Diff for /wikisrc/ports/evbarm/raspberry_pi.mdwn between versions 1.56 and 1.66

version 1.56, 2017/10/14 15:08:18 version 1.66, 2017/10/31 11:32:36
Line 41  Initial, limited, Raspberry Pi support w Line 41  Initial, limited, Raspberry Pi support w
   
  - USB (host); isochronous transfers.   - USB (host); isochronous transfers.
  - WiFi   - WiFi
    - Raspberry Pi 3 in 64-bit mode.  (Note that this will be provided by the evbarm64 port, rather than evbarm.)
   
   # CPU types
   
   Note that one can also use code for earlier models on later models.
   
    - Raspberry Pi 1 uses "earmv6hf".
    - Raspberry Pi 2 uses "earmv7hf".
    - Raspberry Pi 3 uses "earmv7hf".
   
 # Installation  # Installation
   
  - The automatic nightly builds  on [nyftp.netbsd.org](http://nyftp.netbsd.org/pub/NetBSD-daily/) provide image files that can be used for installation. The Raspberry Pi and Pi 2 ports are part of the NetBSD 7 release.  ## SD card structure
     - The 'evbarm-earmv6hf/binary/gzimg/' directory contains an rpi.img file that can be used as a single image for both boards.  
     - The 'evbarm-earmv7hf/binary/gzimg/' directory, as of August 6th 2015, contains an armv7.img file that is optimized for Raspberry Pi 2.  The Raspberry Pi looks for firmware and kernel.img on the first FAT32 partition of the uSD card.  A separate kernel (kernel7.img) is used on RPI2 and RPI3.
     - The stable build directory will be under netbsd-7/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-7/201412161700Z/evbarm-earmv6hf/binary/gzimg/)  
     - The HEAD/current directory build will be under HEAD/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-7/201508062150Z/evbarm-earminstv7hf/binary/gzimg/)  The NetBSD kernel will then use the FFS partition as the root filesystem.
   - You can build your own version of these images using (for example) './build.sh -m evbarm -a earmv6hf -u release', or './build.sh -m evbarm -a earmv7hf -u release'  
    - <i>gunzip and dd</i> this img to your sd card. For example,  A 2 GB card is the smallest workable size.  The NetBSD filesystem will be expanded to fit.
   
   ## Choosing a version
   
   First, decide if you want to install a formal release (7.1), a stable branch build (netbsd-7, netbsd-8), or NetBSD-current.  Note that 7.1 predates Raspberry Pi 3 support.  For people who don't know how to choose among those, netbsd-8 is probably best.
   
   See also "ebijun's image", below, which is NetBSD-current and includes packages.
   
   ## Getting bits to install
   
   You can either build a release yourself with build.sh, or get one from the NetBSD FTP servers.
   
   Both will provide rpi.img.gz and rpi_inst.img.gz.  Each is an image to be written to a uSD card, and has a FAT32 partition for booting.  In rpi.img.gz, there is also an FFS partition for NetBSD.
   
   ### Building yourself
   
   Getting sources and building a release with build.sh is not special for evbarm.  Pick a CPU type alias and pass it to build.sh with -m.  Examples (the first two are equivalent):
   
    - ./build.sh -m earmv6hf -u release
    - ./build.sh -m evbarm -a earmv6hf -u release
    - ./build.sh -m evbarm -a earmv7hf -u release
   
   ### NetBSD FTP servers
   
   NetBSD provides nightly builds on [nyftp.netbsd.org](http://nyftp.netbsd.org/pub/NetBSD-daily/).  These are equivalent to building yourself.
   
    - The 'evbarm-earmv6hf/binary/gzimg/' directory contains an rpi.img file that can be used as a single image for both boards.
    - The 'evbarm-earmv7hf/binary/gzimg/' directory contains an armv7.img file that is optimized for Raspberry Pi 2.
    - The stable build directory will be under netbsd-7/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-7/201710201440Z/evbarm-earmv6hf/binary/gzimg)    
    - The not-yet-released stable build directory will be under netbsd-8/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-8/201710211010Z/evbarm-earmv6hf/binary/gzimg/)
    - The HEAD/current directory build will be under HEAD/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/HEAD/201710202210Z/evbarm-earmv7hf/binary/gzimg/)
   
   ## Preparing a uSD card
   
   Once you have rpi.img.gz (or rpi_inst), put it on a uSD card using gunzip and dd, for example:
   
    - gunzip rpi.img.gz
    - dd if=rpi.i7mg of=/dev/disk1
   
   ### Serial Console
   
   By default the rpi.img is set to use the HDMI output.  If you wish to use a serial console, first mount the FAT32 partition and then
   edit cmdline.txt and remove '"console=fb"'.
   
            dd if=rpi.img of=/dev/disk1   - Most (all?) USB-to-TTL serial adapters only connect Tx, Rx and ground, and do not connect any flow control lines. An effect of missing flow control is that you see console output, but cannot type anything. If so, adjust your serial console application's flow control settings to "none".
   
  - Using a serial console     In Kermit, the command is "set flow none".
    - By default the rpi.img is set to use the HDMI output; to change to using a serial console first mount rpi.img (it's a FAT filesystem)  
   
            edit cmdline.txt and remove '"console=fb"'     In minicom, run "minicom -s" and set hardware flow control to "no"
   
    - Most (all?) USB-to-TTL serial adapters only connect Tx, Rx and ground, and do not connect any flow control lines. An effect of missing flow control is that you see console output, but cannot type anything. If so, adjust your serial console application's flow control settings to "none".  ### Enabling ssh
   
       In Kermit, the command is "set flow none".  If you want to enable ssh with the standard image, so that you can log in over the net without either a serial or HDMI console, mount the ffs partition, place /root/.ssh/authorized_keys, uncomment PermitRootLogin in /etc/ssh/sshd_config, and comment out the rc_configure=NO in /etc/rc.conf.  Besides having to find the IP address, you will have to wait for the partition resizing and reboot.
   
       In minicom, run "minicom -s" and set hardware flow control to "no"  ### Installation with sshramdisk image
   
 ## Installation with sshramdisk image  build.sh (and hence the FTP site) also creates an image 'rpi_inst.img.gz' specifically for installation without HDMI or a serial console.  Note that this image is much smaller and that you will need to fetch the sets over the network.  To use this method, write that image to a uSD card as above, and then:
   
  - You may use the  rpi_inst.img.gz file created by an evbarm build.   - Ensure that you have a lan with a DHCP server.
  - Connect Ethernet Cable to RPI.   - Connect an Ethernet cable from the RPI to the LAN.
  - After starting DHCP client, SSH login to with user "sysinst", and password "netbsd".   - After starting DHCP client, SSH login to with user "sysinst", and password "netbsd".
    - Be careful to note the ip address given during DHCP so you don't lose your connection     - Be careful to note the ip address given during DHCP so you don't lose your connection
    - Also for after the sysinst is done and the system reboots     - Also for after the sysinst is done and the system reboots
Line 76  Initial, limited, Raspberry Pi support w Line 126  Initial, limited, Raspberry Pi support w
   
 ## Installation via ebijun's image  ## Installation via ebijun's image
   
 Jun Ebihara provides an install image for Raspberry Pi that includes  As an alternative to the standard installation images, Jun Ebihara
 packages.  It is based on NetBSD-current.  This image is typically  provides an install image for Raspberry Pi that includes packages.  It
 updated every few weeks.  is based on NetBSD-current and is built for earmv6hf, and thus will
   work on Raspberry Pi 1, 2 and 3.  This image is typically updated
   every few weeks.
   
  - [https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README](https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README)   - [https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README](https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README)
   

Removed from v.1.56  
changed lines
  Added in v.1.66


CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb