Diff for /wikisrc/ports/evbarm/raspberry_pi.mdwn between versions 1.43 and 1.44

version 1.43, 2015/08/03 00:37:05 version 1.44, 2015/08/07 06:58:17
Line 2 Line 2
   
 This page attempts to document and coordinate efforts towards NetBSD/evbarm on [Raspberry Pi](http://www.raspberrypi.org). All board variants are supported.  This page attempts to document and coordinate efforts towards NetBSD/evbarm on [Raspberry Pi](http://www.raspberrypi.org). All board variants are supported.
   
 Initial Raspberry Pi support was introduced in NetBSD 6.0. NetBSD 7.0 adds complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.  Initial, limited, Raspberry Pi support was introduced in NetBSD 6.0. NetBSD 7.0 adds complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.
   
 [[images/raspberrypi.jpg]]  [[images/raspberrypi.jpg]]
   
Line 11  Initial Raspberry Pi support was introdu Line 11  Initial Raspberry Pi support was introdu
 <small>([Raspberry Pi image](http://www.flickr.com/photos/42325803@N07/8118758647/) by Christopher Lee used under CC-By-2.0 license)</small>  <small>([Raspberry Pi image](http://www.flickr.com/photos/42325803@N07/8118758647/) by Christopher Lee used under CC-By-2.0 license)</small>
   
 # Installation  # Installation
  - You may use the rpi.img file created by an evbarm build - evbarm-earmv6hf is recommended. This isn't optimized for Raspberry Pi 2, but allows a single image to be used for all boards.   - The automatic nightly builds  on [nyftp.netbsd.org](http://nyftp.netbsd.org/pub/NetBSD-daily/) provide image files that can be used for installation. The Raspberry Pi and Pi 2 ports will be part of the NetBSD 7 release.
    - The Raspberry Pi and Pi 2 ports will be part of the NetBSD 7 release.      - The 'evbarm-earmv6hf/binary/gzimg/' directory contains an rpi.img file that can be used as a single image for both boards.
    - The automatic nightly builds can be found in the 'evbarm-earmv6hf/binary/gzimg/' directory on [nyftp.netbsd.org](http://nyftp.netbsd.org/pub/NetBSD-daily/).      - The 'evbarm-earmv7hf/binary/gzimg/' directory, as of August 6th 2015, contains an armv7.img file that is optimized for Raspberry Pi 2.
      - The stable build will be under netbsd-7/YYYYMMDDHHMMZ/evbarm-earmv6hf/binary/gzimg/      - The stable build directory will be under netbsd-7/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-7/201412161700Z/evbarm-earmv6hf/binary/gzimg/)
      - The HEAD/current build will be under HEAD/YYYYMMDDHHMMZ/evbarm-earmv6hf/binary/gzimg/      - The HEAD/current directory build will be under HEAD/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-7/201508062150Z/evbarm-earmv7hf/binary/gzimg/)
      - For example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-7/201412161700Z/evbarm-earmv6hf/binary/gzimg/    - You can build your own version of these images using (for example) './build.sh -m evbarm -a earmv6hf -u release', or './build.sh -m evbarm -a earmv7hf -u release'
    - 'releasedir/evbarm/binary/gzimg/' if you run (for example) './build.sh -m evbarm -a earmv6hf -u release'     - <i>gunzip and dd</i> this img to your sd card. For example,
    - <i>gunzip and dd</i> this img to your sd card.  
   
            dd if=rpi.img of=/dev/disk1             dd if=rpi.img of=/dev/disk1
   
Line 33  Initial Raspberry Pi support was introdu Line 32  Initial Raspberry Pi support was introdu
   
       In minicom, run "minicom -s" and set hardware flow control to "no"        In minicom, run "minicom -s" and set hardware flow control to "no"
   
  - Growing the root file-system (**not required with NetBSD -current after 2015-04-07**)   - Growing the root file-system (**not required with NetBSD -current after 2015-04-07, or by NetBSD 7 after 2015-08-06**)
    - During the partitioning process, do not delete or format the     - During the partitioning process, do not delete or format the
      first MSDOS (FAT) partition, as the Raspberry pi firmware is       first MSDOS (FAT) partition, as the Raspberry pi firmware is
      hard coded to boot on the SDCAD / 1st MSDOS partition / Firmware       hard coded to boot on the SDCAD / 1st MSDOS partition / Firmware

Removed from v.1.43  
changed lines
  Added in v.1.44


CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb