Diff for /wikisrc/ports/evbarm/raspberry_pi.mdwn between versions 1.48 and 1.137

version 1.48, 2017/04/21 14:48:31 version 1.137, 2020/10/16 17:29:39
Line 1 Line 1
 [[!meta title="NetBSD/evbarm on Raspberry Pi"]]  [[!meta title="NetBSD/evbarm on Raspberry Pi"]]
   
 This page attempts to document and coordinate efforts towards NetBSD/evbarm on [Raspberry Pi](http://www.raspberrypi.org). All board variants are supported.  This page describes the NetBSD/evbarm port on [Raspberry Pi](http://www.raspberrypi.org) hardware.  All [board variants](https://en.wikipedia.org/wiki/Raspberry_Pi#Specifications) earlier than the RPI4 are believed supported, and specific boards known to work are listed.  We use e.g. "RPI2" to refer to "Raspberry Pi 2" to save precious bytes on this page.  This web page is still 32-bit (aarch32) centric, even though as of mid-2020 aarch64 is also a normal approach.
   
 Initial, limited, Raspberry Pi support was introduced in NetBSD 6.0. NetBSD 7.0 adds complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.  Initial, limited, Raspberry Pi support was introduced in NetBSD 6.0.  NetBSD 7.0 added complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.  Raspberry Pi 3 support was added for NetBSD 8.  NetBSD 9 supports aarch64, meaning using the newer processors in 64-bit mode (via -current in mid 2018).
   
   Overall, this page takes the view that NetBSD 7 and earlier are obsolete; aside from history, it is written as if those versions don't exist.
   
   The HOWTO is written for what works on formal releases, release branches (e.g. netbsd-9) and NetBSD-current.  It purposefully does not contain instructions about how to get things to work by installing code that is still being tested and not yet in -current.
   
 [[images/raspberrypi.jpg]]  [[images/raspberrypi.jpg]]
   
Line 10  Initial, limited, Raspberry Pi support w Line 14  Initial, limited, Raspberry Pi support w
   
 <small>([Raspberry Pi image](http://www.flickr.com/photos/42325803@N07/8118758647/) by Christopher Lee used under CC-By-2.0 license)</small>  <small>([Raspberry Pi image](http://www.flickr.com/photos/42325803@N07/8118758647/) by Christopher Lee used under CC-By-2.0 license)</small>
   
   # What works (and what doesn't yet)
   
   "Works" is primarily relative to the earmv6hf-el and earmv7hf-el CPU targets (32-bit).
   
   ## NetBSD 8
   
    - RPI1, RPI2, RPI2-1.2, RPI3, RPI3+ (except RPI3 builtin WiFi and bluetooth)
    - RPI0 and RPI0W are expected to work (without WiFi, and one needs fdt files \todo where from?)
    - multiple processors on RPI2/RPI3
    - boots normally to multiuser, with FAT32 boot partition on uSD
    - root filesystem can be uSD or USB-attached mass storage
    - serial or graphics console (with EDID query / parsing)
    - X11 via HDMI
    - GPU (VCHIQ) - 3D and video decode. man page missing.
    - USB host controller - dwctwo(4) and most devices work
    - USB Ethernet - usmsc(4)
    - DMA controller driver and sdhc(4) support
    - RNG
    - Audio: works. man page missing.
    - GPIO
    - I²C: works, could use enhancements, man page
    - SPI: could use enhancements, man page
   
   ## NetBSD 9
   
    - aarch64 support (RPI3, and should work on all supported systems with 64-bit CPUs)
    - RPI3 new SD host controller driver
   
   ## NetBSD current
   
    - RPI3 builtin bluetooth
   
   ## (maybe) NetBSD current, with manual steps
   
      These items do not work in the sense that they simply function after a standard install.  Being listed here implies only that there has been list traffic that implies that after taking a bunch of steps (e.g. new firmware, new dtbs, enabling drivers, applying patches), one can end up with the feature working.  The HOWTO explicitly refrains from describing these steps because they are ephemeral.  However, the fact that list traffic indicates success is possible is a clue that proper support is on the horizon, and that is notable.
   
    - RPI3 and RPI0W builtin WiFi
    - RPI4
   
   ## What needs documenting if it works
   
    - (Everything listed in the previous section.)
    - CM1
    - CM3
    - CM3lite
   
   ## What needs work
   
    - USB (host); isochronous transfers.
    - RPI0W Bluetooth Low Energy (probably)
   
   # CPU types
   
    - RPI1 uses "earmv6hf".
    - RPI0 uses "earmv6hf".
    - RPI0W uses "earmv6hf".
    - RPI2 uses "earmv7hf".
    - RPI2-1.2 uses "earmv7hf" or "aarch64" (armv8 CPU hardware)
    - RPI3 uses "earmv7hf" or "aarch64" (armv8 CPU hardware)
    - RPI4 \todo
   
   Note that one can run a build of earmv6hf on the 2 and 3.  There will still be a kernel7, built to use the 2/3 hardware, but with the armv6 instruction set.
   
   In theory the code compiled for earmv7hf will be faster, but anecdotal experience is that it doesn't matter that much.  \todo Post a link to a quality benchmark.
   
   While the evbarm port has "eb" variants (for big-endian mode), the RPI systems do not support eb and these variants will not work.  Systems built for older CPU architectures (earm, earmv4, earmv5) are not expected to work on RPI.
   
   The RPI2-1.2, RPI3 and RPI4 have an armv8 CPU that supports aarch64 (64-bit mode) in addition to aarch32 (regular 32-bit ARM).  This is supported, from 9 onwards, by the "aarch64" MACHINE_ARCH of evbarm, also available in build.sh via the alias evbarm64.  This is also referred to as [[NetBSD/aarch64|aarch64]].
   
 # Installation  # Installation
  - The automatic nightly builds  on [nyftp.netbsd.org](http://nyftp.netbsd.org/pub/NetBSD-daily/) provide image files that can be used for installation. The Raspberry Pi and Pi 2 ports will be part of the NetBSD 7 release.  
     - The 'evbarm-earmv6hf/binary/gzimg/' directory contains an rpi.img file that can be used as a single image for both boards.  
     - The 'evbarm-earmv7hf/binary/gzimg/' directory, as of August 6th 2015, contains an armv7.img file that is optimized for Raspberry Pi 2.  
     - The stable build directory will be under netbsd-7/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-7/201412161700Z/evbarm-earmv6hf/binary/gzimg/)  
     - The HEAD/current directory build will be under HEAD/YYYYMMDDHHMMZ/ (for example, http://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-7/201508062150Z/evbarm-earmv7hf/binary/gzimg/)  
   - You can build your own version of these images using (for example) './build.sh -m evbarm -a earmv6hf -u release', or './build.sh -m evbarm -a earmv7hf -u release'  
    - <i>gunzip and dd</i> this img to your sd card. For example,  
   
            dd if=rpi.img of=/dev/disk1  ## SD card structure
   
  - Using a serial console  The Raspberry Pi looks for firmware and kernel.img on the first FAT32 MBR partition of the uSD card.  A separate kernel (kernel7.img) is used on RPI2 and RPI3.
    - By default the rpi.img is set to use the HDMI output; to change to using a serial console first mount rpi.img (it's a FAT filesystem)  The NetBSD kernel will then find NetBSD MBR partition and within that the root disklabel partition, and use that FFS partition as the root filesystem.
   
            edit cmdline.txt and remove '"console=fb"'  A 2 GB card is the smallest workable size that the installation image will fit on.  After the first boot, the system resizes the NetBSD root partition to fill the card.  Note that swap is after /boot and before /, and not contained in the NetBSD fdisk partition.  However, if you don't try to change the partition structure, this should not cause you any trouble.
   
    - Most (all?) USB-to-TTL serial adapters only connect Tx, Rx and ground, and do not connect any flow control lines. An effect of missing flow control is that you see console output, but cannot type anything. If so, adjust your serial console application's flow control settings to "none".  Note that SD cards generally have limited write tolerance, so you may wish to disable atime updates via the noatime option, as is done by the default installation.
   
       In Kermit, the command is "set flow none".  ## Choosing a version
   
       In minicom, run "minicom -s" and set hardware flow control to "no"  First, decide if you want to install a formal release (8.0 or 9.0), a stable branch build (netbsd-8, netbsd-9), or NetBSD-current.  For people who don't know how to choose among those, a recent build of netbsd-9 is probably best, with 9.0 the choice for those who value being at exactly a formal release.
   
  - Growing the root file-system (**not required with NetBSD -current after 2015-04-07, or by NetBSD 7 after 2015-08-06**)  See also "ebijun's image", below, which is NetBSD-current and includes packages.
    - During the partitioning process, do not delete or format the  
      first MSDOS (FAT) partition, as the Raspberry pi firmware is  
      hard coded to boot on the SDCAD / 1st MSDOS partition / Firmware  
      updates and boot loader.  
    - Copy /boot/cmdline.txt to /boot/cmdline.txt.orig  
    - Edit /boot/cmdline.txt and add the '-s' flag to the end of the first line of text to boot into single-user mode.  
    - For the next steps, the root filesystem mustn't be mounted rw. So reboot, and at the prompt to enter the pathname of shell,  
      press return for the default (/bin/sh).  
    - At the # prompt, type  
   
         "disklabel -i ld0" and press return.  ## Getting bits to install
   
    - At the partition> prompt type "A" and press return.  You can either build a release yourself with build.sh, or get a release from the NetBSD HTTPS/FTP servers.  The bits from both sources should match, except for things like  timestamps, or because the sources are from slightly different points along branches.
   
            Adjust disklabel sector from 4194304 to 62333952 [n]?  ### Building yourself
            Type "y" and press return.  
   
    - partition> prompt type "a" and press return.  Getting sources and building a release with build.sh is not special for evbarm.  However, the evbarm port has a very large number of CPU types, compared to i386 and amd64 which have one each.  The standard approach is to use -m to define MACHINE and -a to define MACHINE_ARCH.  build.sh supports aliases that can be passed as a MACHINE value, but denote both MACHINE and a MACHINE_ARCH.   The third line uses an alias and is equal to the second, for RPI2/3.  Note that the aliases start with "evb" while the MACHINE_ARCH values do not, and that aliases have "-el" or "-eb", while the MACHINE_ARCH values have no suffix or "eb".
   
            Filesystem type prompt, press return to use the current value (4.2BSD).   - ./build.sh -m evbarm -a earmv6hf -u release
            Start offset prompt, press return to use the current value.   - ./build.sh -m evbarm -a earmv7hf -u release
            Partition size prompt, type "$" and press return to grow the   - ./build.sh -m evbearmv7hf-el -u release
            partition to use all available free space.  
   
    - partition> prompt type "W" to save the changes to the disklabel.  Consider setting RELEASEMACHINEDIR if you wish to build multiple MACHINE_ARCH values for a MACHINE; see build.sh.  Use something like "evbarm-earmv7hf", so that 1) earvm6 and earmv7 don't collide and 2) anita will recognize it as a type of evbarm.
   
            Confirm this choice by typing "y" at the Label disk prompt.  ### NetBSD autobuild HTTPS/FTP servers
            Type "Q" and press return to quit disklabel.  
   
    - At the # prompt (shell), type  NetBSD provides nightly builds on [nycdn.netbsd.org](https://nycdn.netbsd.org/pub/NetBSD-daily/).  The next directory level is the branch being built (netbsd-8, netbsd-9, HEAD, and more), plus optionally things like compiler type.  It is followed by date/time, e.g. "HEAD/201811051650Z"; once a build is complete the symlink "latest" is adjusted to point to it.  The next level is "${MACHINE}-${MACHINE_ARCH}", e.g. "evbarm-earmv7hf", and multiple combinations are provided.
   
            fsck -fy /dev/rld0a  An example URL, arguably the standard approach for first-time NetBSD/RPI users, is <https://nycdn.netbsd.org/pub/NetBSD-daily/netbsd-8/latest/evbarm-earmv7hf/binary/gzimg/>
            resize_ffs -y /dev/rld0a  
   
    - This may take a few minutes, be patient!  ### release layout
   
            fsck -fy /dev/rld0a  Once you get to the releasedir, self-built and autobuild releases have the same structure.
            mount_msdos /dev/ld0e /boot  
            mv /boot/cmdline.txt.orig /boot/cmdline.txt  
            reboot  
   
     - When the system comes back up, the root file-system will have been expanded to   - The 'evbarm-earmv6hf/binary/gzimg/' directory contains an rpi.img file that will run on any of the RPI boards.
            fill the SD card.   - The 'evbarm-earmv7hf/binary/gzimg/' directory contains an armv7.img file that uses the armv7 instruction set, and thus can run only on the RPI2 and RPI3 (and perhaps the CM3).  It also supports systems other than the RPI family.
   
 # Installation with sshramdisk image  \todo Explain why there is no armv7_inst.gz.
  - You may use the  rpi_inst.img.gz file created by an evbarm build.  
  - Connect Ethernet Cable to RPI.  
  - After starting DHCP client, SSH login to with user "sysinst", and password "netbsd".  
    - Be careful to note the ip address given during DHCP so you don't lose your connection  
    - Also for after the sysinst is done and the system reboots  
  - sysinst started!  
   
 # Updating the firmware  ## Preparing a uSD card
   
 You probably don't want to do this. Firmware updates can break things,  Once you have rpi.img.gz (or rpi_inst for earmv6 boards), put it on a uSD card using gunzip and dd, for example:
 and the latest firmware that's been tested is already included in the  
 NetBSD build you installed.  
   
 If you're feeling adventurous (or are the port maintainer), here's what   - gunzip rpi.img.gz
 to test whenever you try new firmware:   - dd if=rpi.img of=/dev/disk1
   
 - Audio  ## Console approaches
 - OMXPlayer (and [[!template id=man name="vchiq"]])  
 - Serial/framebuffer console  
 - CPU frequency scaling  
   
 That goes for all of `rpi[0123]`.  The standard approach is to use a USB keyboard and an HDMI monitor for installation.
   
 Upstream firmware releases are  ### Serial Console
 [on GitHub](https://github.com/raspberrypi/firmware/releases).  
 Copy all files except `kernel*.img` into `/boot` and reboot.  By default the rpi.img is set to use the HDMI output.  If you wish to use a serial console, mount the FAT32 partition on another system and edit cmdline.txt and remove '"console=fb"'.
   
    - Most (all?) USB-to-TTL serial adapters have wires for TX, RX and ground, and not RTS/CTS or other flow control lines.   Thus, your terminal program (or terminal) must be configured to not require flow control; a symptom of misconfiguration is that you see console output, but cannot type anything.  If so, adjust your serial console application's flow control settings to "none".   The serial port is at 115200 baud.
   
      - In Kermit, the commands are "set flow none", "set carrier-watch off", "set baud 115200", and, often on NetBSD, "set line /dev/dtyU0".
      - In minicom, run "minicom -s" and set hardware flow control to "no".
   
   ### Enabling ssh for installation without any console
   
   If you want to enable ssh with the standard image, so that you can log in over the net without either a serial or HDMI console, you can edit the configuration of a uSD card before booting.   On another computer, mount the ffs partition, place /root/.ssh/authorized_keys, uncomment PermitRootLogin in /etc/ssh/sshd_config, and comment out the rc_configure=NO in /etc/rc.conf.  Besides having to find the IP address (e.g. from DHCP server logs), you will have to wait for the partition resizing and reboot.
   
   ### Installation with sshramdisk image
   
   build.sh (and hence the FTP site) also creates an image 'rpi_inst.img.gz' specifically for installation without HDMI or a serial console, when built for earmv6hf.  Note that this image is much smaller and that you will need to fetch the sets over the network.  To use this method, write that image to a uSD card as above, and then:
   
    - Connect an Ethernet cable from the RPI to a LAN with a DHCP server, and another host you can use for ssh.
    - Power on the RPI, and wait.  Watch the logs on the DHCP server, and find the IP address assigned to the RPI.
    - Use ssh to log in to the address you found with user "sysinst", and password "netbsd".
    - When installing, ensure that you enable DHCP and ssh, so that you can log in again after the system is installed.
   
   The rpi_inst.img.gz image will only work for systems that use earmv6hf kernels (so not RPI2/3).  See [this port-arm message](https://mail-index.netbsd.org/port-arm/2017/08/18/msg004374.html) for details.
   
   ## Installation via ebijun's image
   
   As an alternative to the standard installation images, Jun Ebihara
   provides an install image for Raspberry Pi that includes packages.  It
   is based on NetBSD-current and is built for earmv6hf, and thus will
   work on Raspberry Pi 1, 2 and 3.  This image is typically updated
   every few weeks.
   
    - <https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README>
   
 # Updating the kernel  ## Boot Process
  - Build a new kernel, e.g. using build.sh. It will tell you where the ELF version of the kernel is, e.g.  
   
   https://www.raspberrypi.org/documentation/configuration/config-txt/boot.md
   
   Note that generally, a single dtb is loaded.  On NetBSD 9, the dtb
   file for the system is loaded by the bootloader (in flash).
   
   ## Configuring 802.11
   
   After installation, the Ethernet will function as on any other NetBSD system; simply enable dhcpcd or configure a static address.  USB WiFi devices will also function as on any other NetBSD system; in addition to dhcpcd or static, configure and enable wpa_supplicant.
   
   Note that the built-in WiFi in the RPI3 is not yet supported.   USB WiFi interfaces (that work on NetBSD in general) should all work.  In particular, the following are known to work:
   
    - urtwn0: Realtek (0xbda) 802.11n WLAN Adapter (0x8176), rev 2.00/2.00, addr 5, MAC/BB RTL8188CUS, RF 6052 1T1R
   
   ## Links
   
   The following pages have been published by NetBSD community members.  (Note that some of them are old.)
   
    - <https://www.cambus.net/netbsd-on-the-raspberry-pi/>
   
   # Maintaining a system
   
   ## Booting single user
   
   \todo Describe how to boot single user via the serial console and via the fb console.
   
   ## vcgencmd
   
   The program vcgencmd, referenced in the boot section,  can be found in pkgsrc/misc/raspberrypi-userland.
   
   ## Updating the kernel
   
    - Run uname -a to determine the name of the config of your current kernel.  For NetBSD <= 8, one ran RPI or RPI2.  For NetBSD >=9, one uses GENERIC.
    - Build a new kernel, e.g. using build.sh. Ideally, run "build.sh release" and look in releasedir/binary/kernels.  If building just a kernel, it will tell you where the ELF version of the kernel is, e.g.
          ...           ...
          Kernels built from RPI2:           Kernels built from GENERIC:
           /Users/feyrer/work/NetBSD/cvs/src-current/obj.evbarm-Darwin-XXX/sys/arch/evbarm/compile/RPI2/netbsd            /Users/feyrer/work/NetBSD/cvs/src-current/obj.evbarm-Darwin-XXX/sys/arch/evbarm/compile/GENERIC/netbsd
          ...           ...
    - There are multiple kernel formats produced by a release build, for use with different boot loader schemes..  For GENERIC:
  - Besides the "netbsd" kernel in ELF format, there is also a "netbsd.bin" kernel that is in a format that the Raspberry can boot.     - netbsd-GENERIC: A normal kernel in ELF format.
      - netbsd-GENERIC.img: In NetBSD >= 9, formatted for the RPI bootloader.
      - netbsd-GENERIC.bin: In NetBSD <= 8, formatted for the RPI bootloader.  In NetBSD >= 9, ??????  In NetBSD 9, this kernel WILL NOT boot.
      - netbsd-GENERIC.ub: A kernel in uboot format.
  - Depending on your hardware version, copy this either to /boot/kernel.img (First generation Pi, Pi Zero hardware) or to /boot/kernel7.img (Pi 2, Pi 3 hardware)   - Depending on your hardware version, copy this either to /boot/kernel.img (First generation Pi, Pi Zero hardware) or to /boot/kernel7.img (Pi 2, Pi 3 hardware)
  - reboot   - reboot
   
 # Wireless Networking  \todo Explain if updating firmware is necessary when e.g. moving from 8 to 9, or 9 to current.
  - A Realtek 802.11n USB adaptor configures as urtwn(4).  
    - Configure with wpa_supplicant in /etc/rc.conf -  ## Updating dtb files
   
            ifconfig_urtwn0=dhcp  
            dhcpcd=YES  
            dhcpcd_flags="-q -b"  
            wpa_supplicant=YES  
            wpa_supplicant_flags="-B -i urtwn0 -c /etc/wpa_supplicant.conf"  
    - A sample wpa_supplicant.conf can be found at /usr/share/examples/wpa_supplicant/wpa_supplicant.conf  
   
 # GPU  ### NetBSD 8
   
   On NetBSD 8, dtb files are not used. (\todo Really?)
   
   ### NetBSD 9
   
   (This is harder than it should be.)
   Build a release.  gunzip the armv7.img, vnconfig it, and mount the MSDOS partition (e) e.g. on /mnt.  Copy the dtb files from /mnt/foo.dtb to /boot, and from /mnt/dtb/foo.dtb to /boot/dtb.
   
   It seems that some systems, including RPI, require dtb files in /boot, and some expect them in /boot/dtb.
   
   \todo Explain if you only really need the right one for your system type.
   
   \todo Explain how one is supposed to be able to update these from the dtb files in releasedir/binary/kernel, or fix it to have the same structure.
   
   ### NetBSD current
   
   When updating, ensure that /boot is mounted and that you unpack the dtb set.
   
   ## Updating the firmware
   
   It is highly likely that running NetBSD from a given branch X with firmware from a branch Y < X will not go well.  It is unclear if firmware from a branch Y > X will work.  It is standard practice to use firmware from the right branch.
   
   A section below describes the process of updating NetBSD's copy of the firmware from upstream, with testing, by NetBSD developers.  This section is about updating a system's firmware from the firmware in a version of NetBSD.
   
   (Updating the firmware is harder than it should be.)
   Build a release.  gunzip the armv7.img, vnconfig it, and mount the MSDOS partition (e) e.g. on /mnt.  Copy files from that to /boot that have changes, carefully.
   
   Relevant files include bootcode.bin, start.elf and start_cd.elf.
   
   Compare cmdline.txt, but beware that just overwriting it will lose customizations like using the serial console instead of the framebuffer.
   
   \todo Explain where the firmware is in the source tree, and note that it is not in the installed system image (such as /usr/mdec).  Explain how to update a system (presumably /boot) from either an installed system's new firmware files, or the source tree.  Explain any particular cautions.
   
   \todo Explain if using updated firmware from one branch (e.g. netbsd-current) on a system using a different branch (e.g. netbsd-8) is safe.  Explain if pullups are done to release branches with new firmware.
   
   ## Booting
   
   The device boots by finding a file "bootcode.bin".   The primary location is a FAT32 partition on the uSD card, and an additional location is on a USB drive.  See the [upstream documentation on booting](https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/) and read all the subpages.
   
   The standard approach is to use a uSD card, with a fdisk partition table containing a FAT32 partition marked active, and a NetBSD partition.  The NetBSD partition will then contain a disklabel, pointing to an FFS partition (a), a swap partition (b) and the FAT32 boot partition mounted as /boot (e).  The file /boot/cmdline.txt has a line to set the root partition.
   
   One wrinkle in the standard approach is that the disk layout is "boot swap /", but the NetBSD fdisk partition starts at the location of /, so the swap partition is not within the NetBSD fdisk partition.  The / partition can hold a disklabel, while swap cannot.   It is normal to have swap after / (and thus within the fdisk partition), but the arrangement used permits growing / on first boot, for the typical case where a larger uSD is used, compared to the minimum image size.
   
   An alternate approach is to have the boot FAT32 partition as above, but to have the entire system including root on an external disk.  This is configured by changing root=ld0a to root=sd0a or root=dk0 (depending on disklabel/GPT).  Besides greater space, part of the point is to avoid writing to the uSD card.
   
   A third approach, workable on the Pi 3 only, is to configure USB host booting (already enabled on the 3+; see the upstream documentation) and have the boot partition also on the external device.  In this case the external device must have an MBR because the hardware's first-stage boot does not have GPT support. In theory the [procedure to program USB host boot mode](https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/msd.md) will function on a NetBSD system because the programming is done by bootcode.bin.
   \todo Confirm that putting program_usb_boot_mode=1 in config.txt and booting works to program the OTP bit.  Confirm that one can then boot NetBSD from external USB.
   
   There is no well-defined USB enumeration order, so the preferred approach if one has multiple USB mass storage devices is to use named wedges in both fstab and cmdline.txt.
   
   ## Split-mode aarch32/aarch64
   
   \todo Verify this, and add any necessary cautions about boot code.
   
   The aarch64 kernel can run aarch32 binaries, so one can boot an aarch64 kernel on a system with an aarch32 userland.
   
   # X11 and GPU
   
 ## Video playback  ## Video playback
 Accelerated video playback is supported in NetBSD 7 with the [OMXPlayer](http://pkgsrc.se/multimedia/omxplayer) application and through GStreamer with the [omx](http://pkgsrc.se/multimedia/gst-plugins1-omx) plugin.  
   Accelerated video playback is supported with the [OMXPlayer](http://pkgsrc.se/multimedia/omxplayer) application and through GStreamer with the [omx](http://pkgsrc.se/multimedia/gst-plugins1-omx) plugin.
   
 ## OpenGL ES  ## OpenGL ES
 Accelerated OpenGL ES is supported in NetBSD 7. The GL ES client libraries are included with the [misc/raspberrypi-userland](http://pkgsrc.se/misc/raspberrypi-userland) package.  
   Accelerated OpenGL ES is supported.  The GL ES client libraries are included with the [misc/raspberrypi-userland](http://pkgsrc.se/misc/raspberrypi-userland) package.
   
 ## Quake 3  ## Quake 3
   
 A Raspberry Pi optimized build of *ioquake3* is available in the [games/ioquake3-raspberrypi](http://pkgsrc.se/games/ioquake3-raspberrypi) package. To use it, the following additional resources are required:  A Raspberry Pi optimized build of *ioquake3* is available in the [games/ioquake3-raspberrypi](http://pkgsrc.se/games/ioquake3-raspberrypi) package. To use it, the following additional resources are required:
   
  - pak0.pk3 from Quake 3 CD   - pak0.pk3 from Quake 3 CD
Line 146  A Raspberry Pi optimized build of *ioqua Line 303  A Raspberry Pi optimized build of *ioqua
 Place the pak0.pk3 file in the /usr/pkg/lib/ioquake3/baseq3 directory.  Place the pak0.pk3 file in the /usr/pkg/lib/ioquake3/baseq3 directory.
   
 ## RetroArch / Libretro  ## RetroArch / Libretro
   
 Using [emulators/retroarch](http://pkgsrc.se/emulators/retroarch) it is possible to run many emulators at full speed the Raspberry Pi. Emulator cores for various gaming consoles are available in the [emulators/libretro-*](http://pkgsrc.se/search.php?so=libretro-) packages. To begin using retroarch:  Using [emulators/retroarch](http://pkgsrc.se/emulators/retroarch) it is possible to run many emulators at full speed the Raspberry Pi. Emulator cores for various gaming consoles are available in the [emulators/libretro-*](http://pkgsrc.se/search.php?so=libretro-) packages. To begin using retroarch:
   
  - Install [emulators/retroarch](http://pkgsrc.se/emulators/retroarch)   - Install [emulators/retroarch](http://pkgsrc.se/emulators/retroarch)
  - Install the libretro core for the system you would like to emulate (lets take [emulators/libretro-gambatte](http://pkgsrc.se/emulators/libretro-gambatte), a GameBoy Color emulator, as an example).   - Install the libretro core for the system you would like to emulate (lets take [emulators/libretro-gambatte](http://pkgsrc.se/emulators/libretro-gambatte), a GameBoy Color emulator, as an example).
  - Plug in a USB HID compatible Gamepad, such as the Logitech F710 in "DirectInput" mode (set "D/X" switch to "D").   - Make sure your user has read and write permissions on `/dev/vchiq`.
  - Create a config file for your gamepad using *retroarch-joyconfig*.   - Plug in a USB HID compatible Gamepad, such as the Logitech F710 in "DirectInput" mode (set "D/X" switch to "D"). Note that since the framebuffer GL driver will not allow for keyboard input in RetroArch, you will have to copy your joypad configuration from another system.
 [[!template  id=programlisting text="""   - Configure retroarch by editing $HOME/.config/retroarch/retroarch.cfg:
 $ retroarch-joyconfig -o gamepad.cfg          video_driver = "gl"
 """]]          input_driver = "null"
  - Launch the emulator from the command-line (no X required):          joypad_driver = "sdl2"
 [[!template  id=programlisting text="""          menu_driver = "rgui"
 $ retroarch --appendconfig gamepad.cfg -L /usr/pkg/lib/libretro/gambatte_libretro.so game.gbc  
   # Developer notes
   
   These notes are for people working on improvements to RPI support in NetBSD.
   
   ## Updating the firmware version in the NetBSD sources
   
   (Note that trying new firmware may result in a non-bootable system, so
   be prepared to recover the bootable media with another system.)
   
   Upstream firmware releases are
   [on GitHub](https://github.com/raspberrypi/firmware/releases).
   Copy all files except `kernel*.img` into `/boot` and reboot.
   
   New firmware should pass all of the following tests before being committed to NetBSD.
   
   - Audio
   - OMXPlayer (and [[!template id=man name="vchiq"]])
   - Serial/framebuffer console
   - CPU frequency scaling
   
   Tests should be run on all of `rpi[0123]`.
   
   ## Testing with anita and qemu
   
   See the anita section in the evbarm page.
   
   It is not currently known how to emulate a RPI in qemu, and therefore anita does not yet have support for this.  \todo Add a command-line example to run qemu emulating some RPI model.
   
   # Misc notes
   
   Miscellaneous notes about Raspberry PI.
   
   ## Power supply needed (or: why there is a little rainbow square in the top-right corner?)
   
   Raspberry Pi devices are powered by 5V micro USB and a 2.5A (2500mA)
   power supply is recommended.  For more information please read:
   
    <https://www.raspberrypi.org/documentation/faqs/#pi-power>
   
   Power glitches can also manifest in other ways, e.g. with an USB
   disk plugged:
   
   [[!template id=programlisting text="""
   sd0(umass0:0:0:0): generic HBA error
   sd0: cache synchronization failed
 """]]  """]]
   
 # What works (NetBSD 7.0+)  Using a recommended power supply avoid such issues.
  - multi-user boot with root on SD card  
  - serial or graphics console (with EDID query / parsing)  
  - DMA controller driver and sdhc(4) support  
  - Audio: works. man page missing.  
  - I²C: works, could use enhancements, man page  
  - GPIO  
  - RNG  
  - SPI: could use enhancements, man page  
  - GPU (VCHIQ) - 3D and video decode. man page missing.  
  - USB (host) - dwctwo(4)  
  - USB Ethernet - usmsc(4)  
  - X windows.  
  - RaspberryPi 2 SMP  
   
 # What needs work  ## Xenon death flash (Raspberry Pi 2 is camera-shy)
  - USB (host); isochronous transfers.  
   When using laser pointers or xenon flashes in cameras (or other
   flashes of high-intensity long-wave light) against a Raspberry Pi
   2 the Pi can power itself off.
   For more information please read:
   
    <https://www.raspberrypi.org/blog/xenon-death-flash-a-free-physics-lesson/>

Removed from v.1.48  
changed lines
  Added in v.1.137


CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb