Diff for /wikisrc/ports/evbarm/raspberry_pi.mdwn between versions 1.86 and 1.121

version 1.86, 2018/11/06 03:13:59 version 1.121, 2019/09/02 20:48:37
Line 1 Line 1
 [[!meta title="NetBSD/evbarm on Raspberry Pi"]]  [[!meta title="NetBSD/evbarm on Raspberry Pi"]]
   
 This page attempts to document and coordinate efforts towards NetBSD/evbarm on [Raspberry Pi](http://www.raspberrypi.org). All board variants are supported.  This page describes the NetBSD/evbarm port on [Raspberry Pi](http://www.raspberrypi.org) hardware.  All [board variants](https://en.wikipedia.org/wiki/Raspberry_Pi#Specifications) earlier than the RPI4 are believed supported, and specific boards known to work are listed.  We use e.g. "RPI2" to refer to "Raspberry Pi 2" to save precious bytes on this page.  This web page is 32-bit (aarch32) centric, as that has been until mid-2018 the only approach.
   
 Initial, limited, Raspberry Pi support was introduced in NetBSD 6.0. NetBSD 7.0 adds complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.  Raspberry Pi 3 support was added for NetBSD 8, and backported to NetBSD 7 in July of 2017.  (This page assumes those using NetBSD 7 are using 7.2, or the netbsd-7 branch after mid 2018.)  Initial, limited, Raspberry Pi support was introduced in NetBSD 6.0.  NetBSD 7.0 adds complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.  Raspberry Pi 3 support was added for NetBSD 8, and backported to NetBSD 7 in July of 2017.  (This page assumes those using NetBSD 7 are using 7.2 or later, but note that everyone uses 8 or -current.)
   
   In mid-2018, -current gained support for 64-bit ARM (aarch64) support.  This will be in NetBSD 9.
   
 [[images/raspberrypi.jpg]]  [[images/raspberrypi.jpg]]
   
Line 14  Initial, limited, Raspberry Pi support w Line 16  Initial, limited, Raspberry Pi support w
   
 ## NetBSD 7 and NetBSD 8  ## NetBSD 7 and NetBSD 8
   
  - RaspberryPi 1, 2, 3 (except Pi 3 builtin WiFi and bluetooth)   - RPI1, RPI2, RPI2-1.2, RPI3, RPI3+ (except RPI3 builtin WiFi and bluetooth)
  - multiple processors on 2/3   - RPI0 and RPI0W are expected to work (without WiFi, and one needs fdt files \todo where from?)
    - multiple processors on RPI2/RPI3
  - boots normally to multiuser, with FAT32 boot partition on uSD   - boots normally to multiuser, with FAT32 boot partition on uSD
  - root filesystem can be uSD or USB-attached mass storage   - root filesystem can be uSD or USB-attached mass storage
  - serial or graphics console (with EDID query / parsing)   - serial or graphics console (with EDID query / parsing)
Line 32  Initial, limited, Raspberry Pi support w Line 35  Initial, limited, Raspberry Pi support w
   
 ## NetBSD current  ## NetBSD current
   
  - Raspberry Pi 3 builtin bluetooth   - RPI3+ 
  - Raspberry Pi 3 new SD host controller driver   - RPI3 builtin bluetooth
    - RPI3 new SD host controller driver
    - \todo Verify: RPI2-1.2 and RPI3 aarch64
   
   ## What needs documenting if it works
   
    - CM1
    - CM3
    - CM3lite
   
 ## What needs work  ## What needs work
   
    - RPI4 (almost certainly; not clear)
  - USB (host); isochronous transfers.   - USB (host); isochronous transfers.
  - Raspberry Pi 3 builtin WiFi   - RPI3, RPI0W builtin WiFi
    - RPI0W Bluetooth Low Energy (probably)
    - aarch64 support is evolving very rapidly, and not yet recommended for production, largely because one must run -current.
   
 # CPU types  # CPU types
   
  - Raspberry Pi 1 uses "earmv6hf".   - RPI1 uses "earmv6hf".
  - Raspberry Pi 0 uses "\todo".   - RPI0 uses "earmv6hf".
  - Raspberry Pi 2 uses "earmv7hf".   - RPI0W uses "earmv6hf".
  - Raspberry Pi 3 uses "earmv7hf".   - RPI2 uses "earmv7hf".
  - Raspberry Pi 0W uses "\todo".   - RPI2-1.2 uses "earmv7hf" or "aarch64" (armv8 CPU hardware)
    - RPI3 uses "earmv7hf" or "aarch64" (armv8 CPU hardware)
 Note that one can run earmv6hf code on the 2 and 3.  See also  
 [[NetBSD/aarch64|aarch64]] for running the Pi 2/3 in 64-bit mode.  Note that one can run a build of earmv6hf on the 2 and 3.  There will still be a kernel7, built to use the 2/3 hardware, but with the armv6 instruction set.
   
   In theory the code compiled for earmv7hf will be faster, but anecdotal experience is that it doesn't matter that much.
   
   While the evbarm port has "eb" variants (for big-endian mode), the RPI systems do not support eb and these variants will not work.  Systems built with older CPU architectures (earm, earmv4, earmv5) are not expected to work on RPI.
   
   The RPI2-1.2 and RPI3 have an armv8 CPU that supports aarch64 (64-bit
   mode) in addition to aarch32 (regular 32-bit ARM).  This is supported,
   in -current only, by the "aarch64" MACHINE_ARCH of evbarm, also
   available in build.sh via the alias evbarm64.  This is sometimes
   referred to as [[NetBSD/aarch64|aarch64]].
   
 # Installation  # Installation
   
Line 60  The NetBSD kernel will then find NetBSD  Line 84  The NetBSD kernel will then find NetBSD 
   
 A 2 GB card is the smallest workable size, and the installation image will fit.  After the first boot, the system resizes the NetBSD root partition to fill the card.  Note that swap is after /boot and before /, and not contained in the NetBSD fdisk partition.  However, if you don't try to change the partition structure, this should not cause you any trouble.  A 2 GB card is the smallest workable size, and the installation image will fit.  After the first boot, the system resizes the NetBSD root partition to fill the card.  Note that swap is after /boot and before /, and not contained in the NetBSD fdisk partition.  However, if you don't try to change the partition structure, this should not cause you any trouble.
   
   Note that SD cards generally have limited write tolerance, so you may wish to disable atime updates via the noatime option, as is done by the default installation.
   
 ## Choosing a version  ## Choosing a version
   
 First, decide if you want to install a formal release (7.2 or 8.0), a stable branch build (netbsd-7, netbsd-8), or NetBSD-current.  For people who don't know how to choose among those, 8.0 or netbsd-8 is probably best.  First, decide if you want to install a formal release (7.2 or 8.0), a stable branch build (netbsd-7, netbsd-8), or NetBSD-current.  For people who don't know how to choose among those, a recent build of netbsd-8 is probably best, with 8.0 the choice for those who value being at exactly a formal release.
   
 See also "ebijun's image", below, which is NetBSD-current and includes packages.  See also "ebijun's image", below, which is NetBSD-current and includes packages.
   
 ## Getting bits to install  ## Getting bits to install
   
 You can either build a release yourself with build.sh, or get one from the NetBSD FTP servers.  You can either build a release yourself with build.sh, or get a release from the NetBSD HTTPS/FTP servers.  The bits from both sources should match, except for things like  timestamps, or because the sources are from slightly different points along branches.
   
 Both will provide rpi.img.gz and rpi_inst.img.gz.  Each is an image to be written to a uSD card, and has a FAT32 partition for booting.  In rpi.img.gz, there is also an FFS partition for NetBSD.  
   
 ### Building yourself  ### Building yourself
   
 Getting sources and building a release with build.sh is not special for evbarm.  However, the evbarm port has a very large number of CPU types, compared to i386 and amd64 which have one.  The standard approach is to use -m to define MACHINE and -a to define MACHINE_ARCH.  build.sh supports aliases that can be passed as a MACHINE value, but denote both MACHINE and a MACHINE_ARCH.   The third line uses an alias and is equal to the second in effect, for RPI2/3.  Getting sources and building a release with build.sh is not special for evbarm.  However, the evbarm port has a very large number of CPU types, compared to i386 and amd64 which have one each.  The standard approach is to use -m to define MACHINE and -a to define MACHINE_ARCH.  build.sh supports aliases that can be passed as a MACHINE value, but denote both MACHINE and a MACHINE_ARCH.   The third line uses an alias and is equal to the second, for RPI2/3.  Note that the aliases start with "evb" while the MACHINE_ARCH values do not, and that aliases have "-el" or "-eb", while the MACHINE_ARCH values have no suffix or "eb".
   
  - ./build.sh -m evbarm -a earmv6hf -u release   - ./build.sh -m evbarm -a earmv6hf -u release
  - ./build.sh -m evbarm -a earmv7hf -u release   - ./build.sh -m evbarm -a earmv7hf -u release
  - ./build.sh -m earmv7hf-el -u release   - ./build.sh -m evbearmv7hf-el -u release
   
 Consider setting RELEASEMACHINEDIR if you wish to build multiple MACHINE_ARCH values on the same system; see build.sh.  Consider setting RELEASEMACHINEDIR if you wish to build multiple MACHINE_ARCH values for a MACHINE; see build.sh.  Use something like "evbarm-earmv7hf", so that 1) earvm6 and earmv7 don't collide and 2) anita will recognize it as a type of evbarm.
   
 ### NetBSD autobuild HTTPS/FTP servers  ### NetBSD autobuild HTTPS/FTP servers
   
 NetBSD provides nightly builds on [nyftp.netbsd.org](https://nyftp.netbsd.org/pub/NetBSD-daily/).  These are equivalent to building yourself.  The next directory level is the branch being built (netbsd-7, netbsd-8, HEAD, and more), plus optionally things like compiler type.  It is followed by date/time, e.g. "HEAD/201811051650Z"; once a build is complete the symlink "latest" is adjusted to point to it.  The next level is "${MACHINE}-${MACHINE_ARCH}", e.g. "evbarm-earmv7hf", and multiple combinations are provided.  NetBSD provides nightly builds on [nycdn.netbsd.org](https://nycdn.netbsd.org/pub/NetBSD-daily/).  The next directory level is the branch being built (netbsd-7, netbsd-8, HEAD, and more), plus optionally things like compiler type.  It is followed by date/time, e.g. "HEAD/201811051650Z"; once a build is complete the symlink "latest" is adjusted to point to it.  The next level is "${MACHINE}-${MACHINE_ARCH}", e.g. "evbarm-earmv7hf", and multiple combinations are provided.
   
   An example URL, arguably the standard approach for first-time NetBSD/RPI users, is https://nycdn.netbsd.org/pub/NetBSD-daily/netbsd-8/latest/evbarm-earmv7hf/binary/gzimg/
   
   ### release layout
   
   Once you get to the releasedir, self-built and autobuild releases have the same structure.
   
  - The 'evbarm-earmv6hf/binary/gzimg/' directory contains an rpi.img file that will run on any of the RPI boards.   - The 'evbarm-earmv6hf/binary/gzimg/' directory contains an rpi.img file that will run on any of the RPI boards.
  - The 'evbarm-earmv7hf/binary/gzimg/' directory contains an armv7.img file that uses the armv7 instruction set, and thus can run only on the Raspberry Pi 2/3, but is also faster than rpi.img.   - The 'evbarm-earmv7hf/binary/gzimg/' directory contains an armv7.img file that uses the armv7 instruction set, and thus can run only on the RPI2 and RPI3 (and perhaps the CM3).  It also supports systems other than the RPI family.
   
 An example URL, arguably the standard approach for beginners, is https://nyftp.netbsd.org/pub/NetBSD-daily/netbsd-8/latest/evbarm-earmv7hf/binary/gzimg/  \todo Explain why there is no armv7_inst.gz.
   
 ## Preparing a uSD card  ## Preparing a uSD card
   
 Once you have rpi.img.gz (or rpi_inst), put it on a uSD card using gunzip and dd, for example:  Once you have rpi.img.gz (or rpi_inst for earmv6 boards), put it on a uSD card using gunzip and dd, for example:
   
  - gunzip rpi.img.gz   - gunzip rpi.img.gz
  - dd if=rpi.img of=/dev/disk1   - dd if=rpi.img of=/dev/disk1
   
 ### Serial Console  ## Console approaches
   
   The standard approach is to use a USB keyboard and an HDMI monitor for installation.
   
 By default the rpi.img is set to use the HDMI output.  If you wish to use a serial console, first mount the FAT32 partition and then  ### Serial Console
 edit cmdline.txt and remove '"console=fb"'.  
   
  - Most (all?) USB-to-TTL serial adapters only connect Tx, Rx and ground, and do not connect any flow control lines. An effect of missing flow control is that you see console output, but cannot type anything. If so, adjust your serial console application's flow control settings to "none".  By default the rpi.img is set to use the HDMI output.  If you wish to use a serial console, mount the FAT32 partition on another system and edit cmdline.txt and remove '"console=fb"'.
   
    In Kermit, the command is "set flow none".   - Most (all?) USB-to-TTL serial adapters have wires for TX, RX and ground, and not RTS/CTS or other flow control lines.   Thus, your terminal program (or terminal) must be configured to not require flow control; a symptom of misconfiguration is that you see console output, but cannot type anything.  If so, adjust your serial console application's flow control settings to "none".
   
    In minicom, run "minicom -s" and set hardware flow control to "no"     - In Kermit, the command is "set flow none".
      - In minicom, run "minicom -s" and set hardware flow control to "no".
   
 ### Enabling ssh  ### Enabling ssh for installation without any console
   
 If you want to enable ssh with the standard image, so that you can log in over the net without either a serial or HDMI console, mount the ffs partition, place /root/.ssh/authorized_keys, uncomment PermitRootLogin in /etc/ssh/sshd_config, and comment out the rc_configure=NO in /etc/rc.conf.  Besides having to find the IP address, you will have to wait for the partition resizing and reboot.  If you want to enable ssh with the standard image, so that you can log in over the net without either a serial or HDMI console, you can edit the configuration of a uSD card before booting.   On another computer, mount the ffs partition, place /root/.ssh/authorized_keys, uncomment PermitRootLogin in /etc/ssh/sshd_config, and comment out the rc_configure=NO in /etc/rc.conf.  Besides having to find the IP address (e.g. from DHCP server logs), you will have to wait for the partition resizing and reboot.
   
 ### Installation with sshramdisk image  ### Installation with sshramdisk image
   
 build.sh (and hence the FTP site) also creates an image 'rpi_inst.img.gz' specifically for installation without HDMI or a serial console.  Note that this image is much smaller and that you will need to fetch the sets over the network.  To use this method, write that image to a uSD card as above, and then:  build.sh (and hence the FTP site) also creates an image 'rpi_inst.img.gz' specifically for installation without HDMI or a serial console, when built for earmv6hf.  Note that this image is much smaller and that you will need to fetch the sets over the network.  To use this method, write that image to a uSD card as above, and then:
   
    - Connect an Ethernet cable from the RPI to a LAN with a DHCP server, and another host you can use for ssh.
    - Power on the RPI, and wait.  Watch the logs on the DHCP server, and find the IP address assigned to the RPI.
    - Use ssh to login to the address you found with user "sysinst", and password "netbsd".
    - When installing, ensure that you enable DHCP and ssh, so that you can log in again after the system is installed.
   
  - Ensure that you have a lan with a DHCP server.  The rpi_inst.img.gz image will only work for systems that use earmv6hf kernels (so not RPI2/3).  See [this port-arm message](https://mail-index.netbsd.org/port-arm/2017/08/18/msg004374.html) for details.
  - Connect an Ethernet cable from the RPI to the LAN.  
  - After starting DHCP client, SSH login to with user "sysinst", and password "netbsd".  
    - Be careful to note the ip address given during DHCP so you don't lose your connection  
    - Also for after the sysinst is done and the system reboots  
  - sysinst started!  
   
 ## Installation via ebijun's image  ## Installation via ebijun's image
   
Line 132  is based on NetBSD-current and is built  Line 164  is based on NetBSD-current and is built 
 work on Raspberry Pi 1, 2 and 3.  This image is typically updated  work on Raspberry Pi 1, 2 and 3.  This image is typically updated
 every few weeks.  every few weeks.
   
  - [https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README](https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README)   - <https://github.com/ebijun/NetBSD/blob/master/RPI/RPIimage/Image/README>
   
   ## Configuring 802.11
   
   After installation, the Ethernet will function as on any other NetBSD system; simply enable dhcpcd or configure a static address.  USB WiFi devices will also function as on any other NetBSD system; in addition to dhcpcd or static, configure and enable wpa_supplicant.
   
   Note that the built-in WiFi in the RPI3 is not yet supported.   USB WiFi interfaces (that work on NetBSD in general) should all work.  In particular, the following are known to work:
   
    - urtwn0: Realtek (0xbda) 802.11n WLAN Adapter (0x8176), rev 2.00/2.00, addr 5, MAC/BB RTL8188CUS, RF 6052 1T1R
   
   ## Links
   
   The following pages have been published by NetBSD community members.  (Note that some of them are old.)
   
    - https://www.cambus.net/netbsd-on-the-raspberry-pi/
   
 # Maintaining a system  # Maintaining a system
   
Line 157  The program vcgencmd, referenced in the  Line 203  The program vcgencmd, referenced in the 
   
 A section below describes the process of updating NetBSD's copy of the firmware from upstream, with testing, by NetBSD developers.  This section is about updating a system's firmware from the firmware in a version of NetBSD.  A section below describes the process of updating NetBSD's copy of the firmware from upstream, with testing, by NetBSD developers.  This section is about updating a system's firmware from the firmware in a version of NetBSD.
   
 TODO: Explain where the firmware is in the source tree, and if it is in the installed system image (such as /usr/mdec).  Explain any particular cautions.  \todo Explain where the firmware is in the source tree, and if it is in the installed system image (such as /usr/mdec).  Explain how to update a system (presumably /boot) from either an installed system's new firmware files, or the source tree.  Explain any particular cautions.
   
   Probably, for the RPI3+, one needs to use -current, or use -8 with firmware from -current.  \todo Defuzz.
   
   \todo Explain if using updated firmware from one branch (e.g. netbsd-current) on a system using a different branch (e.g. netbsd-8) is safe.  Explain if pullups are done to release branches with new firmware.
   
 ## Booting  ## Booting
   
 The device boots by finding a file "bootcode.bin".   The primary location is a FAT32 partition on the uSD card, and an additional location is on a USB drive.  See the [upstream documentation on booting](https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/) and read all the subpages.  The device boots by finding a file "bootcode.bin".   The primary location is a FAT32 partition on the uSD card, and an additional location is on a USB drive.  See the [upstream documentation on booting](https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/) and read all the subpages.
   
 The standard approach is to use a uSD card, with a fdisk partition table containing a FAT32 partition marked active, and a NetBSD partition.  The NetBSD partition will then contain a disklabel, pointing to an FFS partition (a), a swap paritiion (b) and the FAT32 boot partition mounted as /boot (e).  The file /boot/cmdline.txt has a line to set the root partition.  The standard approach is to use a uSD card, with a fdisk partition table containing a FAT32 partition marked active, and a NetBSD partition.  The NetBSD partition will then contain a disklabel, pointing to an FFS partition (a), a swap partition (b) and the FAT32 boot partition mounted as /boot (e).  The file /boot/cmdline.txt has a line to set the root partition.
   
 One wrinkle in the standard approach is that the disk layout is "boot swap /", but the NetBSD fdisk partition starts at the location of /.   The / partition can hold a disklabel, while swap cannot.   It is normal to have swap after / (and thus within the fdisk partition), but the arrangement used permits growing / on first boot, for the typical case where a larger uSD is used, compared to the minimum image size.  One wrinkle in the standard approach is that the disk layout is "boot swap /", but the NetBSD fdisk partition starts at the location of /, so the swap partition is not within the NetBSD fdisk partition.  The / partition can hold a disklabel, while swap cannot.   It is normal to have swap after / (and thus within the fdisk partition), but the arrangement used permits growing / on first boot, for the typical case where a larger uSD is used, compared to the minimum image size.
   
 An alternate approach is to have the boot FAT32 partition as above, but to have the entire system including root on an external disk.  This is configured by changing root=ld0a to root=sd0a or root=dk0 (depending on disklabel/GPT).  Besides greater space, part of the point is to avoid writing to the uSD card.  An alternate approach is to have the boot FAT32 partition as above, but to have the entire system including root on an external disk.  This is configured by changing root=ld0a to root=sd0a or root=dk0 (depending on disklabel/GPT).  Besides greater space, part of the point is to avoid writing to the uSD card.
   
 A third approach, workable on the Pi 3 only, is to configure USB host booting (already enableed on the 3+; see the upstream documentation) and have the boot partition also on the external device.  In this case the external device must have an MBR because the hardware's first-stage boot does not have GPT support. In theory the [procedure to program USB host boot mode](https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/msd.md) will function on a NetBSD system because the programming is done by bootcode.bin.  A third approach, workable on the Pi 3 only, is to configure USB host booting (already enableed on the 3+; see the upstream documentation) and have the boot partition also on the external device.  In this case the external device must have an MBR because the hardware's first-stage boot does not have GPT support. In theory the [procedure to program USB host boot mode](https://www.raspberrypi.org/documentation/hardware/raspberrypi/bootmodes/msd.md) will function on a NetBSD system because the programming is done by bootcode.bin.
 \todo Confirm that putting program_usb_boot_mode=1 in config.txt and booting works to program the OTP bit.  Confirm that one can then boot NetBSD from external USB.  \todo Confirm that putting program_usb_boot_mode=1 in config.txt and booting works to program the OTP bit.  Confirm that one can then boot NetBSD from external USB.
   
 \todo Explain USB enumeration and how to ensure that the correct boot and root devices are found if one has e.g. a small SSD for the system and a big disk.  There is no well-defined USB enumeration order, so the preferred approach if one has multiple USB mass storage devices is to use named wedges in both fstab and cmdline.txt.
   
 # Wireless Networking  
   
 Note that the built-in WiFi in the RPI3 is not yet supported.   USB WiFi interfaces (that work on NetBSD in general) should all work.  ## Split-mode aarch32/aarch64
   
  - A Realtek 802.11n USB adaptor configures as urtwn(4).  \todo Verify this, and add any necessary cautions about boot code.
    - Configure with wpa_supplicant in /etc/rc.conf -  
   
            ifconfig_urtwn0=dhcp  The aarch64 kernel can run aarch32 binaries, so one can boot a aarch64 kernel on a system with aarch32 userland.
            dhcpcd=YES  
            dhcpcd_flags="-q -b"  
            wpa_supplicant=YES  
            wpa_supplicant_flags="-B -i urtwn0 -c /etc/wpa_supplicant.conf"  
    - A sample wpa_supplicant.conf can be found at /usr/share/examples/wpa_supplicant/wpa_supplicant.conf  
   
 # GPU  # X11 and GPU
   
 ## Video playback  ## Video playback
 Accelerated video playback is supported in NetBSD 7 with the [OMXPlayer](http://pkgsrc.se/multimedia/omxplayer) application and through GStreamer with the [omx](http://pkgsrc.se/multimedia/gst-plugins1-omx) plugin.  Accelerated video playback is supported in NetBSD 7 with the [OMXPlayer](http://pkgsrc.se/multimedia/omxplayer) application and through GStreamer with the [omx](http://pkgsrc.se/multimedia/gst-plugins1-omx) plugin.
Line 210  Using [emulators/retroarch](http://pkgsr Line 252  Using [emulators/retroarch](http://pkgsr
   
  - Install [emulators/retroarch](http://pkgsrc.se/emulators/retroarch)   - Install [emulators/retroarch](http://pkgsrc.se/emulators/retroarch)
  - Install the libretro core for the system you would like to emulate (lets take [emulators/libretro-gambatte](http://pkgsrc.se/emulators/libretro-gambatte), a GameBoy Color emulator, as an example).   - Install the libretro core for the system you would like to emulate (lets take [emulators/libretro-gambatte](http://pkgsrc.se/emulators/libretro-gambatte), a GameBoy Color emulator, as an example).
  - Plug in a USB HID compatible Gamepad, such as the Logitech F710 in "DirectInput" mode (set "D/X" switch to "D").   - Make sure your user has read and write permissions on `/dev/vchiq`.
  - Create a config file for your gamepad using *retroarch-joyconfig*.   - Plug in a USB HID compatible Gamepad, such as the Logitech F710 in "DirectInput" mode (set "D/X" switch to "D"). Note that since the framebuffer GL driver will not allow for keyboard input in RetroArch, you will have to copy your joypad configuration from another system.
 [[!template  id=programlisting text="""   - Configure retroarch by editing $HOME/.config/retroarch/retroarch.cfg:
 $ retroarch-joyconfig -o gamepad.cfg          video_driver = "gl"
 """]]          input_driver = "null"
  - Launch the emulator from the command-line (no X required):          joypad_driver = "sdl2"
 [[!template  id=programlisting text="""          menu_driver = "rgui"
 $ retroarch --appendconfig gamepad.cfg -L /usr/pkg/lib/libretro/gambatte_libretro.so game.gbc  
 """]]  
   
 # Developer notes  # Developer notes
   
Line 240  New firmware should pass all of the foll Line 280  New firmware should pass all of the foll
 - Serial/framebuffer console  - Serial/framebuffer console
 - CPU frequency scaling  - CPU frequency scaling
   
 Tests shoudl be run on all of `rpi[0123]`.  Tests should be run on all of `rpi[0123]`.
   
   ## Testing with anita and qemu
   
   See the anita section in the evbarm page.
   
   It is not currently known how to emulate a RPI in qemu, and therefore anita does not yet have support for this.  \todo Add a command-line example to run qemu emulating some RPI model.
   
   
   # Misc notes
   Miscellaneous notes about Raspberry PI.
   
   ## Power supply needed (or: why there is a little rainbow square in the top-right corner?)
   Raspberry Pi devices are powered by 5V micro USB and a 2.5A (2500mA)
   power supply is reccomended.  For more information please read:
   
    <https://www.raspberrypi.org/documentation/faqs/#pi-power>
   
   Power glitches can also manifest in other ways, e.g. with an USB
   disk plugged:
   
   [[!template id=programlisting text="""
   sd0(umass0:0:0:0): generic HBA error
   sd0: cache synchronization failed
   """]]
   
   Using a reccomended power supply avoid such issues.
   
   ## Xenon death flash (Raspberry Pi 2 is camera-shy)
   When using laser pointers or xenon flashes in cameras (or other
   flashes of high-intensity long-wave light) against a Raspberry Pi
   2 the Pi can power itself off.
   For more information please read:
   
    <https://www.raspberrypi.org/blog/xenon-death-flash-a-free-physics-lesson/>

Removed from v.1.86  
changed lines
  Added in v.1.121


CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb