Diff for /wikisrc/ports/evbarm/raspberry_pi.mdwn between versions 1.107 and 1.109

version 1.107, 2018/11/06 22:42:38 version 1.109, 2018/11/07 01:10:59
Line 52  Initial, limited, Raspberry Pi support w Line 52  Initial, limited, Raspberry Pi support w
 # CPU types  # CPU types
   
  - RPI1 uses "earmv6hf".   - RPI1 uses "earmv6hf".
  - RPI0 uses "\todo".   - RPI0 uses "earmv6hf".
    - RPI0W uses "earmv6hf".
  - RPI2 uses "earmv7hf".   - RPI2 uses "earmv7hf".
  - RPI3 uses "earmv7hf".   - RPI3 uses "earmv7hf".
  - RPI0W uses "\todo".  
   
 Note that one can run a build of earmv6hf on the 2 and 3.  There will still be a kernel7, built to use the 2/3 hardware, but with the armv6 instruction set.  Note that one can run a build of earmv6hf on the 2 and 3.  There will still be a kernel7, built to use the 2/3 hardware, but with the armv6 instruction set.
   
Line 126  The standard approach is to use a USB ke Line 126  The standard approach is to use a USB ke
   
 By default the rpi.img is set to use the HDMI output.  If you wish to use a serial console, mount the FAT32 partition on another system and edit cmdline.txt and remove '"console=fb"'.  By default the rpi.img is set to use the HDMI output.  If you wish to use a serial console, mount the FAT32 partition on another system and edit cmdline.txt and remove '"console=fb"'.
   
  - Most (all?) USB-to-TTL serial adapters have wires for Tx, Rx and ground, and not RTS/CTS or other flow control lines.   Thus, your terminal program (or terminal) must be configured to not require flow control; a symptom of misconfiguration is that you see console output, but cannot type anything.  If so, adjust your serial console application's flow control settings to "none".   - Most (all?) USB-to-TTL serial adapters have wires for TX, RX and ground, and not RTS/CTS or other flow control lines.   Thus, your terminal program (or terminal) must be configured to not require flow control; a symptom of misconfiguration is that you see console output, but cannot type anything.  If so, adjust your serial console application's flow control settings to "none".
   
    - In Kermit, the command is "set flow none".     - In Kermit, the command is "set flow none".
    - In minicom, run "minicom -s" and set hardware flow control to "no".     - In minicom, run "minicom -s" and set hardware flow control to "no".
Line 144  build.sh (and hence the FTP site) also c Line 144  build.sh (and hence the FTP site) also c
  - Use ssh to login to the address you found with user "sysinst", and password "netbsd".   - Use ssh to login to the address you found with user "sysinst", and password "netbsd".
  - When installing, ensure that you enable DHCP and ssh, so that you can log in again after the system is installed.   - When installing, ensure that you enable DHCP and ssh, so that you can log in again after the system is installed.
   
 \todo Verify that the above is accurate and sufficient.  
   
 The rpi_inst.img.gz image will only work for systems that use earmv6hf kernels (so not RPI2/3).  See [this port-arm message](https://mail-index.netbsd.org/port-arm/2017/08/18/msg004374.html) for details.  The rpi_inst.img.gz image will only work for systems that use earmv6hf kernels (so not RPI2/3).  See [this port-arm message](https://mail-index.netbsd.org/port-arm/2017/08/18/msg004374.html) for details.
   
 ## Installation via ebijun's image  ## Installation via ebijun's image

Removed from v.1.107  
changed lines
  Added in v.1.109


CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb