Diff for /wikisrc/ports/evbarm/raspberry_pi.mdwn between versions 1.103 and 1.108

version 1.103, 2018/11/06 22:29:26 version 1.108, 2018/11/07 00:56:20
Line 2 Line 2
   
 This page attempts to document and coordinate efforts towards NetBSD/evbarm on [Raspberry Pi](http://www.raspberrypi.org).  All [board variants](https://en.wikipedia.org/wiki/Raspberry_Pi#Specifications) are supported.  We use e.g. "RPI2" to refer to "Raspberry Pi 2" to save precious bytes on this page.  This page attempts to document and coordinate efforts towards NetBSD/evbarm on [Raspberry Pi](http://www.raspberrypi.org).  All [board variants](https://en.wikipedia.org/wiki/Raspberry_Pi#Specifications) are supported.  We use e.g. "RPI2" to refer to "Raspberry Pi 2" to save precious bytes on this page.
   
 Initial, limited, Raspberry Pi support was introduced in NetBSD 6.0. NetBSD 7.0 adds complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.  Raspberry Pi 3 support was added for NetBSD 8, and backported to NetBSD 7 in July of 2017.  (This page assumes those using NetBSD 7 are using 7.2, or the netbsd-7 branch after mid 2018.)  Initial, limited, Raspberry Pi support was introduced in NetBSD 6.0.  NetBSD 7.0 adds complete support for the board, along with introducing support for the quad-core Raspberry Pi 2 board.  Raspberry Pi 3 support was added for NetBSD 8, and backported to NetBSD 7 in July of 2017.  (This page assumes those using NetBSD 7 are using 7.2 or later, but note that everyone uses 8 or -current.)
   
 [[images/raspberrypi.jpg]]  [[images/raspberrypi.jpg]]
   
Line 33  Initial, limited, Raspberry Pi support w Line 33  Initial, limited, Raspberry Pi support w
   
 ## NetBSD current  ## NetBSD current
   
  - RPI3B+    - RPI3+ 
  - RPI3 builtin bluetooth   - RPI3 builtin bluetooth
  - RPI3 new SD host controller driver   - RPI3 new SD host controller driver
   
Line 46  Initial, limited, Raspberry Pi support w Line 46  Initial, limited, Raspberry Pi support w
 ## What needs work  ## What needs work
   
  - USB (host); isochronous transfers.   - USB (host); isochronous transfers.
  - RPI3 builtin WiFi   - RPI3, RPI0W builtin WiFi
    - RPI0W Bluetooth Low Energy (probably)
   
 # CPU types  # CPU types
   
Line 112  Once you get to the releasedir, self-bui Line 113  Once you get to the releasedir, self-bui
   
 ## Preparing a uSD card  ## Preparing a uSD card
   
 Once you have rpi.img.gz (or rpi_inst), put it on a uSD card using gunzip and dd, for example:  Once you have rpi.img.gz (or rpi_inst for earmv6 boards), put it on a uSD card using gunzip and dd, for example:
   
  - gunzip rpi.img.gz   - gunzip rpi.img.gz
  - dd if=rpi.img of=/dev/disk1   - dd if=rpi.img of=/dev/disk1
Line 143  build.sh (and hence the FTP site) also c Line 144  build.sh (and hence the FTP site) also c
  - Use ssh to login to the address you found with user "sysinst", and password "netbsd".   - Use ssh to login to the address you found with user "sysinst", and password "netbsd".
  - When installing, ensure that you enable DHCP and ssh, so that you can log in again after the system is installed.   - When installing, ensure that you enable DHCP and ssh, so that you can log in again after the system is installed.
   
 \todo Verify that the above is accurate and sufficient.  The rpi_inst.img.gz image will only work for systems that use earmv6hf kernels (so not RPI2/3).  See [this port-arm message](https://mail-index.netbsd.org/port-arm/2017/08/18/msg004374.html) for details.
   
 ## Installation via ebijun's image  ## Installation via ebijun's image
   
Line 194  A section below describes the process of Line 195  A section below describes the process of
   
 \todo Explain where the firmware is in the source tree, and if it is in the installed system image (such as /usr/mdec).  Explain how to update a system (presumably /boot) from either an installed system's new firmware files, or the source tree.  Explain any particular cautions.  \todo Explain where the firmware is in the source tree, and if it is in the installed system image (such as /usr/mdec).  Explain how to update a system (presumably /boot) from either an installed system's new firmware files, or the source tree.  Explain any particular cautions.
   
 Probably, for the RPI3B+, one needs to use -current, or use -8 with firmware from -current.  \todo Defuzz.  Probably, for the RPI3+, one needs to use -current, or use -8 with firmware from -current.  \todo Defuzz.
   
 \todo Explain if using updated firmware from one branch (e.g. netbsd-current) on a system using a different branch (e.g. netbsd-8) is safe.  Explain if pullups are done to release branches with new firmware.  \todo Explain if using updated firmware from one branch (e.g. netbsd-current) on a system using a different branch (e.g. netbsd-8) is safe.  Explain if pullups are done to release branches with new firmware.
   
Line 271  Tests should be run on all of `rpi[0123] Line 272  Tests should be run on all of `rpi[0123]
   
 anita has support for evbarm.  Install qemu and dtb-arm-vexpress from pkgsrc.  Note that the release subdirectory should be evbarm-earmv6hf or evbarm-earmv7hf.  anita has support for evbarm.  Install qemu and dtb-arm-vexpress from pkgsrc.  Note that the release subdirectory should be evbarm-earmv6hf or evbarm-earmv7hf.
   
 \todo Explain how to select various RPI models to emulate.  \todo It is not currently known and documented how to configure qemu and anita to emulate a RPI in general or a specific RPI model.
   
 \todo Explain about how DTB works.  \todo Explain about how DTB works.
   
 \todo Give a command line example to run qemu (without anita).  \todo Give a command line example to run qemu (without anita).

Removed from v.1.103  
changed lines
  Added in v.1.108


CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb