Diff for /wikisrc/ports/evbarm/qemu_arm.mdwn between versions 1.8 and 1.10

version 1.8, 2019/12/03 12:52:20 version 1.10, 2021/07/16 09:36:13
Line 7  This can be extremely useful for develop Line 7  This can be extremely useful for develop
 # Requirements  # Requirements
 * qemu 4.1.0 or higher  * qemu 4.1.0 or higher
 * disk image  * disk image
   * [NetBSD 9.x armv7](http://nycdn.netbsd.org/pub/NetBSD-daily/netbsd-9/latest/evbarm-earmv7hf/binary/gzimg/armv7.img.gz)    * [NetBSD 9.x armv7](https://nycdn.netbsd.org/pub/NetBSD-daily/netbsd-9/latest/evbarm-earmv7hf/binary/gzimg/armv7.img.gz)
   * [NetBSD 9.x arm64](http://nycdn.netbsd.org/pub/NetBSD-daily/netbsd-9/latest/evbarm-aarch64/binary/gzimg/arm64.img.gz)    * [NetBSD 9.x arm64](https://nycdn.netbsd.org/pub/NetBSD-daily/netbsd-9/latest/evbarm-aarch64/binary/gzimg/arm64.img.gz)
 * Tianocore EDK2 firmware  * Tianocore EDK2 firmware
   * [QEMU_EFI.fd for armv7](http://snapshots.linaro.org/components/kernel/leg-virt-tianocore-edk2-upstream/latest/QEMU-ARM/RELEASE_GCC5/QEMU_EFI.fd)    * [QEMU_EFI.fd for armv7](https://snapshots.linaro.org/components/kernel/leg-virt-tianocore-edk2-upstream/4276/QEMU-ARM/RELEASE_GCC5/QEMU_EFI.fd)
   * [QEMU_EFI.fd for arm64](http://snapshots.linaro.org/components/kernel/leg-virt-tianocore-edk2-upstream/latest/QEMU-AARCH64/RELEASE_GCC5/QEMU_EFI.fd)    * [QEMU_EFI.fd for arm64](https://snapshots.linaro.org/components/kernel/leg-virt-tianocore-edk2-upstream/4276/QEMU-AARCH64/RELEASE_GCC5/QEMU_EFI.fd)
   
 # Installing QEMU on NetBSD  # Installing QEMU on NetBSD
 You can install latest qemu with the following commands.  You can install latest qemu with the following commands.
Line 41  The disk image (armv7.img.gz or arm64.im Line 41  The disk image (armv7.img.gz or arm64.im
           -netdev type=user,id=net0 -device virtio-net-device,netdev=net0,mac=00:11:22:33:44:55 \            -netdev type=user,id=net0 -device virtio-net-device,netdev=net0,mac=00:11:22:33:44:55 \
           -bios QEMU_EFI.fd -nographic            -bios QEMU_EFI.fd -nographic
   
   # Enabling graphics support
   To enable graphics support, remove the following command-line argument:
   
       -nographic
   
   and replace it with:
   
       -display sdl,gl=on -device ramfb -device usb-ehci,id=ehci \
       -device usb-mouse,bus=ehci.0 -device usb-kbd,bus=ehci.0
   
 # Bridged networking  # Bridged networking
   
 To bridge a QEMU guest to your network, you need to create a tap(4) interface for your VM, then connect it to a physical interface with a bridge(4) interface.  To bridge a QEMU guest to your network, you need to create a tap(4) interface for your VM, then connect it to a physical interface with a bridge(4) interface.

Removed from v.1.8  
changed lines
  Added in v.1.10


CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb