1: [[!template id=port
16: NetBSD/evbarm is the port of NetBSD to various evaluation and prototyping
17: boards based on CPUs implementing the ARM architecture. NetBSD/evbarm also
18: supports some specific embedded system products based on prototype board
21: ### CPU types
23: The evbarm port can be built with a variety of CPU options, corresponding to the
24: [large array of ARM CPU architectures](https://en.wikipedia.org/wiki/ARM_architecture#Cores).
25: There are
26: four main variables: the word size, the instruction set, the
27: endianness, and whether there is hardware floating point. By default
28: the CPU type is "earm", and this implies aarch32 (32-bit), earmv5 cpu
29: architecture, little endian (el when explicitly stated), and soft
30: (Emulated) floating point. Another example, suitable for Raspberry PI
31: 2, is earmv7hf, which is aarch32, the v7 instruction set, little
32: endian, and hardware floating point.
34: Typically, various boards are best compiled with a CPU type that
35: matches the board's CPU and floating point support, but generally a
36: lower CPU instruction set version is workable on a newer board. See
37: build.sh and look for aliases for the evbarm port.
39: Through NetBSD 8, the evbarm port has supported exclusively the
40: aarch32 (32-bit CPU) sub-family of the ARM architecture. Some
41: processors, such as many supporting the armv8 CPU architecture, also
42: support a 64-bit instruction set, referred to as aarch64. This is
43: sometimes referred to as a distinct port, [[NetBSD/aarch64|aarch64]],
44: with code in src/sys/arch/aarch64, but it is built as the evbarm port
45: with aarch64 cpu type, and available as the alias evbarm64.
47: Note that MACHINE_ARCH=aarch64 currently refers to the A64 instruction
48: set and the aarch64 architecture, built for the armv8 architecture.
49: (Note also that armv8 is the first architecture to support aarch64, so
50: this will not be an issue until at least armv9.)
52: ### QEMU
54: See the [[NetBSD/evbarm under QEMU|qemu_arm]] page for instructions on how to get started with QEMU.
56: ### anita
58: anita can be used to test builds. (In addition to anita, install qemu and dtb-arm-vexpress from pkgsrc.) The release subdirectory should follow the naming convention on the autobuild cluster, used below.
60: - evbarm-earmv7hf uses "qemu-system-arm -M vexpress-a15"
61: - evbarm-aarch64 uses "qemu-system-aarch64 -M virt"
62: - Information on how to test emulated versions of other specific hardware is welcome.
64: ### invisible.ca builds
66: NetBSD developer Jared McNeill provides [builds of NetBSD-current for a vast variety of hardware.](https://www.invisible.ca/arm/) In addition to the standard build, these images have board-specific uboot contents. See also /usr/pkgsrc/sysutils/u-boot*.
68: ### Board specific information (often including installation information)
69: - [[Allwinner sunxi family SoCs|Allwinner]]
70: - [[BeagleBone, BeagleBone Black, and PocketBeagle|BeagleBone]]
71: - [[NVIDIA Tegra|Tegra]]
72: - [[ODROID C1 and C1+|ODROID-C1]]
73: - [[Raspberry Pi 1, 2 and 3|Raspberry Pi]]
75: ### SSH configuration for installtion
77: The default configuration will connect to the local network via DHCP and
78: run an SSH server. In order to use the SSH server, we must configure
79: users. This can be done by writing to the SD card's MS-DOS partition.
81: Create a creds.txt file and use:
83: useradd user password
85: <!--TODO: Additional configuration options are available on creds_msdos.8-->
90: **NOTE**: This list is incomplete. For a full list of boards, please see the [GENERIC DTS files](http://cvsweb.netbsd.org/bsdweb.cgi/~checkout~/src/sys/arch/evbarm/conf/GENERIC).
92: [[!toc startlevel=3]]
94: ### ADI Engineering **BRH** ("Big Red Head")
96: The BRH is an evaluation and development platform for the Intel **i80200**
97: XScale processor. The BRH is based on ADI's **BECC** ("Big Endian Companion
98: Chip"). The BRH is capable of both big- and little-endian operation, although
99: NetBSD currently only supports little-endian operation.
101: Support for the BRH was written by Jason Thorpe, and contributed by Wasabi
102: Systems, Inc.
104: * On-board NS16550-compatible serial ports (_com_)
105: * On-board Intel i82559 Ethernet on the PCI bus (_fxp_)
106: * On-chip timer on the BECC (used as system clock)
107: * Other devices inserted into the PCI slot
109: The BRH comes with 128M of SDRAM. Systems with BECC revision 7 or less are
110: limited to 64M due to the layout of the PCI DMA windows. Users of these
111: systems should obtain an FPGA upgrade from ADI to revision 8 or later of the
114: ### Allwinner Technology
115: Various boards based on [[Allwinner]] SoCs are supported, including the BananaPi, Cubieboard 2, Cubietruck, Cubieboard 4, and Merrii Hummingbird A31.
117: ### Arcom **Viper**
119: The Arcom Viper is a single board computer based on the PXA255 XScale
122: Support for the Arcom Viper was written by Antti Kantee.
124: * On-chip timers (_saost_ used as system clock)
125: * On-chip serial ports (_com_)
126: * On-board SMC91C111 ethernet (_sm_)
128: ### ARM, Ltd. **Integrator**
130: The Integrator/AP is an ATX form-factor board that is used for development of
131: ARM processor-based designs. It supports up to four processors on plug-in core
132: modules, and provides clocks, a bus interface, and interrupt support. The
133: Integrator/AP also supports logic modules which provide additional
134: peripherals, and can accommodate up to three PCI expansion cards. The
135: Integrator/AP can also be inserted into a CompactPCI backplane.
137: Support for the Integrator was written by Richard Earnshaw, and contributed by
138: ARM, Ltd.
140: * PrimeCell PL010 UARTs in the System Controller FPGA (_plcom_)
141: * PrimeCell PL030 Real-time Clock in the System Controller FPGA (_plrtc_)
142: * PrimeCell PL181 MultiMedia Card Interface
143: * Other devices inserted into the PCI expansion slots
145: ### Atmark Techno **Armadillo-9**
147: The Armadillo-9 is a single board computer based on the EP9315 processor.
149: Support for the Armadillo-9 was written by Katsuomi Hamajima.
151: * On-CPU RS232 UARTs (2) (_epcom_)
152: * On-CPU 10/100 Ethernet MAC (_epe_)
153: * system clock from on-CPU timers (_epclk_)
154: * CompactFlash socket (_eppcic_)
155: * USB 1.1 ports (_ohci_)
157: ### BeagleBoard.org **BeagleBoard** and **BeagleBoard-xM**
158: The [[BeagleBoard]] is a low-power open-source hardware single-board computer from BeagleBoard.org.
160: ### BeagleBoard.org **BeagleBone** and **BeagleBone Black**
161: The [[BeagleBone]] is a low-cost credit-card-sized computer from BeagleBoard.org.
163: ### Gumstix, Inc. **gumstix**
165: The [gumstix](http://www.gumstix.com/) is a small form-factor motherboard
166: based on the PXA255 and PXA270 XScale processor. Supports only PXA255 now.
168: Support for the gumstix was written by KIYOHARA Takashi.
170: * basix
171: * cfstix
172: * etherstix
173: * netCF
174: * netDUO
175: * netDUO-mmc
176: * netMMC
178: When booting, it is necessary to set these with u-boot dynamically.
180: <pre> > go 0xa0200000 busheader=basix</pre>
182: * audiostix
183: * console-st (waysmall - STUART)
184: * console-hw (waysmall)
185: * GPSstix (GPS not test)
186: * tweener
188: ### Hardkernel ODROID-C1 and ODROID-C1+
190: The [[ODROID-C1]] is a quad core Cortex-A5 small form-factor board from Hardkernel co., Ltd.
192: ### Intel **DBPXA250** ("Lubbock")
194: DBPXA250 (a.k.a. Lubbock) is an evaluation and development platform for the
195: Intel **PXA250** XScale Core application processor. More information about the **DBPXA250** can be found at [Intel website](http://www.intel.com/design/pca/applicationsprocessors/swsup/index.htm).
197: Support for the **DBPXA250** was written by Hiroyuki Bessho, and contributed
198: by Genetec Corp.
200: * On-chip timers (_saost_ used as system clock)
201: * On-chip 2 serial port (_com_)
202: * On-board SMC91C96 ethernet (_sm_)
203: * On-board SA-1111 StrongArm companion chip (_sacc_)
204: * PS/2 keyboard (_pckbd_)
205: * 640x480 LCD (_lcd_)
206: * PCMCIA and CF card slots
208: ### Intel **IQ31244**
210: The IQ31244 is a development platform for the Intel **IOP321** I/O Processor
211: chipset and the Intel **i31244** SATA controller.
213: Initial support for the IQ31244 was written by Jason Thorpe, and contributed
214: by Wasabi Systems, Inc.
216: * Quad on-board Intel i31244 SATA controllers on the PCI-X bus (_artsata_)
217: * On-board Intel i82546EB Gigabit Ethernet on the PCI-X bus (_wm_)
218: * On-board NS16550-compatible serial port (_com_)
219: * On-chip timers (TMR0 used as system clock)
220: * On-chip Application Accelerator Unit (_iopaau_)
221: * On-chip watchdog timer (_iopwdog_)
222: * On-board compact flash reader (_wdc_)
223: * Other devices inserted into the PCI-X expansion slot
225: ### Intel **IQ80310**
227: The IQ80310 is the reference platform for the Intel **IOP310** I/O Processor
228: chipset, which is comprised of the i80200 XScale processor and the i80312 I/O
229: Companion chip.
231: Support for the IQ80310 was written by Jason Thorpe and Allen Briggs, and
232: contributed by Wasabi Systems, Inc.
234: * On-board Intel i82559 Ethernet on the PCI bus (_fxp_)
235: * On-board timer in the CPLD (used as system clock)
236: * On-board NS16550-compatible serial ports (_com_)
237: * Other devices inserted into the PCI expansion slots
239: ### Intel **IQ80321**
241: The IQ80321 is the reference platform for the Intel **IOP321** I/O Processor
242: (i80321 XScale processor).
244: Support for the IQ80321 was written by Jason Thorpe, and contributed by Wasabi
245: Systems, Inc.
247: * On-board Intel i82544EI Gigabit Ethernet on the PCI-X bus (_wm_)
248: * On-board NS16550-compatible serial port (_com_)
249: * On-chip timers (TMR0 used as system clock)
250: * On-chip Application Accelerator Unit (_iopaau_)
251: * On-chip watchdog timer (_iopwdog_)
252: * Other devices inserted into the PCI-X expansion slots
254: ### Intel **IXM1200**
256: The IXM1200 is the reference platform for the Intel **IXP1200** Network
259: Support for the IXM1200 was written by Ichiro FUKUHARA and Naoto Shimazaki.
261: * On-board Intel i82559 Ethernet on the PCI bus (_fxp_)
262: * On-board Intel i21555 Non-Transparent PCI-PCI Bridge (_nppb_)
263: * On-chip timers (ixpclk0 used as system clock)
264: * On-chip serial port (_ixpcom_)
266: ### NOVATEC **NTNP425B** ("ZAO425")
268: NTNP425B is an evaluation and development platform for the Intel **IXP425**
269: XScale Core NetworkProcessor. NTNP425B is based on the reference board of
270: Intel **IXDP425**. The **NTNP425B** is capable of only big-endian operation.
271: Since the library for micro-engine(NPE) offered from Intel Corp. is big-
272: endian. More information about the **NTNP425B** can be found on [product
273: catalogue of **NTNP425B**(2.5MB,PDF
276: Support for the NTNP425B was written by Ichiro FUKUHARA.
278: * On-chip timers (_ixpclk0_ used as system clock)
279: * On-chip 2 serial port (_ixpcom0_ and _ixpcom1_)
280: * Other devices inserted into the PCI/mPCI slot
281: * On-chip watchdog timer (_ixpwdog_)
283: ### NVIDIA Tegra K1
284: Support for NVIDIA [[Tegra]] K1 SoCs is present in NetBSD-current and
285: 8.0_BETA. The Jetson TK1 board is currently supported.
287: ### Raspberry Pi Foundation **Raspberry Pi**/**Raspberry Pi 2**/**Raspberry Pi 3**
288: The [[Raspberry Pi]] is a low-cost credit-card-sized computer from the Raspberry Pi Foundation. The Raspberry Pi, Pi 2, and Pi 3 are supported.
290: See the [[Raspberry Pi 1, 2 and 3|Raspberry Pi]] page for much more information.
292: ### Samsung **SMDK2410**
294: The SMDK2410 is the reference platform for the Samsung **S3C2410** processor,
295: which has an ARM920T core.
297: More information on the S3C2410 can be found at [Samsung Electronics web page]
301: Support for the SMDK2410 was written by Hiroyuki Bessho, and contributed by
302: Genetec Corp.
304: * On-chip serial ports (_sscom_)
305: * On-chip USB host controller (_ohc_)
306: * On-chip timers (used as system clock)
307: * On-chip SPI (_ssspi_, used for other on-board devices)
308: * 240x320 TFT LCD (_lcd_)
309: * keyboard. (_sskbd_)
311: ### Samsung **SMDK2800**
313: The SMDK2800 is the reference platform for the **Samsung S3C2800** processor,
314: which has an ARM920T core.
316: S3C2800 has built-in PCI controller, and SMDK2800 has three PCI slots.
318: Support for the SMDK2800 was written by Hiroyuki Bessho, and contributed by
319: Fujitsu Component Ltd., and Genetec Corp.
321: * On-chip serial ports (_sscom_)
322: * On-chip Host-PCI bridge (_sspci_)
323: * On-chip timers (used as system clock)
324: * Other devices inserted into the PCI slots
326: ### Team ASA, Inc. **Npwr**
328: The Npwr is an IOP310-based design targeted at the network-attached storage
329: space. The Npwr comes in several configurations (single or dual Gigabit
330: Ethernet, single or dual Ultra160 SCSI), and can be purchased as a bare board
331: or as a small server appliance. More information on the Npwr can be found at
332: the [Team ASA web page](http://www.teamasa.com/).
334: Support for the Npwr was written by Jason Thorpe and Allen Briggs, and
335: contributed by Wasabi Systems, Inc.
337: * On-board Intel i82544 Gigabit Ethernet on the PCI bus (_wm_)
338: * On-board LSI Logic 53c1010 Ultra160 SCSI on the PCI bus (_siop_)
339: * On-board timer in the CPLD (used as system clock)
340: * On-board NS16550-compatible serial port (_com_)
342: ### Technologic Systems **TS-7200**
344: The TS-7200 is a low-cost mass-produced PC/104 embedded single board computer
345: intended as a general purpose core for real embedded applications. The TS-7200
346: uses the Cirrus Logic EP9302 ARM9 system-on-chip and comes with a PC/104 (isa)
347: bus and can either boot to CompactFlash or onboard flash. The board also has
348: general purpose digital IO and optional multichannel analog-to-digital
349: converters. More information on the TS-7200 can be found at [Technologic
352: Support for the TS-7200 was written by Jesse Off
354: * On-CPU RS232 UARTs (2) (_epcom_)
355: * On-CPU 10/100 Ethernet MAC (_epe_)
356: * CompactFlash socket (_wdc_)
357: * USB 1.1 ports (2) (_ohci_)
358: * Watchdog timer on CPLD (_tspld_)
359: * TMP124 high precision temperature sensor via sysctl
360: * 64Hz system clock from on-CPU timers (_epclk_)
361: * HD44780 2x24 text mode LCD (_tslcd_)
362: * 4x4 16 button matrix keypad (_wskbd_)
363: * TS-5620 battery backed RTC daughter-card (_tsrtc_)
364: * 1,2,4 port serial TS-SER daughter cards (_com_)
365: * Up to 4 10Mb TS-ETH10 daughter cards (_tscs_)
366: * Other devices inserted into the PC/104 (_isa_) expansion slot
370: * The [NetBSD Diskless HOWTO](http://www.netbsd.org/docs/network/netboot/)
371: * [ Porting NetBSD/evbarm to the Arcom Viper](http://www.cs.hut.fi/~pooka/pubs/EuroBSDCon2005/viper.pdf), presented at EuroBSDCon 2005.
374: [[!tag tier1port]]
CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb