NetBSD/evbarm is the port of NetBSD to various systems based on chips
implementing the ARM architecture. The "evb" component is a reference
to evaluation boards, the original target of the port. However, the
single GENERIC/GENERIC64 kernel now supports a range of machines including
development boards, virtual machines, "ServerReady" (SBBR/SBSA) hardware,
and laptops through both device tree and ACPI based booting. [Friendly image downloads](http://www.armbsd.org/arm/)
### CPU types
Various CPU variants are supported, e.g:
- evbarm-earmv6hf - ARMv6-A with EABI and hardware floating point, e.g.
the original Raspberry Pi.
- evbarm-earmv7hf - ARMv7-A with EABI and hardware floating point, e.g.
most recent and common 32-bit ARM boards.
- evbarm-earmv7hfeb - Same as the above, but with the CPU running in
big endian mode.
- evbarm-aarch64 - 64-bit ARMv8-A boards.
- evbarm-aarch64eb - Same as the above, but with the CPU running in
big endian mode.
Since NetBSD 9.0, 64-bit ARM processors are supported (referred to here
as aarch64). These run with fully 64-bit kernels and userland. Running
32-bit ARM binaries is also supported with `compat32`. The 64-bit
kernel supports up to 256 CPUs and the 32-bit kernel supports up to 8.
Since NetBSD 9.0, there is support for symmetric and asymmetrical
multiprocessing (aka big.LITTLE).
evbarm variants are little endian unless otherwise stated. NetBSD provides
big endian images primarily for testing purposes and to ensure that the code
### Board specific information (often including installation information)
- [[Allwinner sunxi family SoCs|Allwinner]]
- [[Apple Silicon|Apple]]
- [[BeagleBone, BeagleBone Black, and PocketBeagle|BeagleBone]]
- [[NVIDIA Tegra|Tegra]]
- [[ODROID C1 and C1+|ODROID-C1]]
- [[Raspberry Pi 1, 2 and 3|Raspberry Pi]]
- [[RockChip SoCs|RockChip]]
- [[Terasic DE0 Nano-SoC|Cyclone5]]
**NOTE**: This list is incomplete. For a full list of supported device tree
based boards, please see the list of
[64-bit](https://github.com/NetBSD/src/blob/netbsd-9/sys/arch/evbarm/conf/GENERIC64#L20) device trees.
See the [[NetBSD/evbarm under QEMU|qemu_arm]] page for instructions on how to get started with QEMU.
### armbsd.org builds
NetBSD developer Jared McNeill provides [builds of NetBSD 9 and -current for a vast variety of hardware.](http://www.armbsd.org/arm/) In addition to the standard build, these images have board-specific U-Boot contents. See also /usr/pkgsrc/sysutils/u-boot*.
### SSH configuration
The default configuration will connect to the local network via DHCP and
run an SSH server.
In order to use the SSH server, we must configure users.
This can be done by writing to the SD card's MS-DOS partition.
Create a creds.txt file and use:
useradd user password
See [creds_msdos(8)](https://man.NetBSD.org/creds_msdos.8) for
additional configuration options.
anita can be used to test builds. (In addition to anita, install qemu and dtb-arm-vexpress from pkgsrc.) The release subdirectory should follow the naming convention on the autobuild cluster, used below.
- evbarm-earmv7hf uses 'qemu-system-arm -M vexpress-a15'
- evbarm-aarch64 uses 'qemu-system-aarch64 -M virt'
- Information on how to test emulated versions of other specific hardware is welcome.
CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb