Annotation of wikisrc/guide/raidframe.mdwn, revision 1.10
1.10 ! jdf 1: **Contents**
! 2:
! 3: [[!toc levels=3]]
! 4:
1.1 jdf 5: # NetBSD RAIDframe
6:
7: ## RAIDframe Introduction
8:
9: ### About RAIDframe
10:
1.6 jdf 11: NetBSD uses the [CMU RAIDframe](http://www.pdl.cmu.edu/RAIDframe/) software for
12: its RAID subsystem. NetBSD is the primary platform for RAIDframe development.
13: RAIDframe can also be found in older versions of FreeBSD and OpenBSD. NetBSD
14: also has another way of bundling disks, the
15: [ccd(4)](http://netbsd.gw.com/cgi-bin/man-cgi?ccd+4+NetBSD-5.0.1+i386) subsystem
16: (see [Concatenated Disk Device](/guide/ccd)). You should possess some [basic
17: knowledge](http://www.acnc.com/04_00.html) about RAID concepts and terminology
18: before continuing. You should also be at least familiar with the different
19: levels of RAID - Adaptec provides an [excellent
20: reference](http://www.adaptec.com/en-US/_common/compatibility/_education/RAID_level_compar_wp.htm),
21: and the [raid(4)](http://netbsd.gw.com/cgi-bin/man-cgi?raid+4+NetBSD-5.0.1+i386)
1.1 jdf 22: manpage contains a short overview too.
23:
24: ### A warning about Data Integrity, Backups, and High Availability
25:
1.6 jdf 26: RAIDframe is a Software RAID implementation, as opposed to Hardware RAID. As
27: such, it does not need special disk controllers supported by NetBSD. System
28: administrators should give a great deal of consideration to whether software
29: RAID or hardware RAID is more appropriate for their "Mission Critical"
30: applications. For some projects you might consider the use of many of the
31: hardware RAID devices [supported by
32: NetBSD](http://www.NetBSD.org/support/hardware/). It is truly at your discretion
33: what type of RAID you use, but it is recommend that you consider factors such
1.1 jdf 34: as: manageability, commercial vendor support, load-balancing and failover, etc.
35:
1.6 jdf 36: Depending on the RAID level used, RAIDframe does provide redundancy in the event
37: of a hardware failure. However, it is *not* a replacement for reliable backups!
38: Software and user-error can still cause data loss. RAIDframe may be used as a
39: mechanism for facilitating backups in systems without backup hardware, but this
40: is not an ideal configuration. Finally, with regard to "high availability", RAID
1.1 jdf 41: is only a very small component to ensuring data availability.
42:
43: Once more for good measure: *Back up your data!*
44:
45: ### Hardware versus Software RAID
46:
1.6 jdf 47: If you run a server, it will most probably already have a Hardware RAID
48: controller. There are reasons for and against using a Software RAID, depending
1.1 jdf 49: on the scenario.
50:
1.6 jdf 51: In general, a Software RAID is well suited for low-IO system disks. If you run a
52: Software RAID, you can exchange disks and disk controllers, or even move the
53: disks to a completely different machine. The computational overhead for the RAID
1.1 jdf 54: is negligible if there is only few disk IO operations.
55:
1.6 jdf 56: If you need much IO, you should use a Hardware RAID. With a Software RAID, the
57: redundancy data has to be transferred via the bus your disk controller is
58: connected to. With a Hardware RAID, you transfer data only once - the redundancy
1.1 jdf 59: computation and transfer is done by the controller.
60:
61: ### Getting Help
62:
1.6 jdf 63: If you encounter problems using RAIDframe, you have several options for
1.1 jdf 64: obtaining help.
65:
1.6 jdf 66: 1. Read the RAIDframe man pages:
67: [raid(4)](http://netbsd.gw.com/cgi-bin/man-cgi?raid+4+NetBSD-5.0.1+i386) and
68: [raidctl(8)](http://netbsd.gw.com/cgi-bin/man-cgi?raidctl+8+NetBSD-5.0.1+i386)
1.1 jdf 69: thoroughly.
70:
1.6 jdf 71: 2. Search the mailing list archives. Unfortunately, there is no NetBSD list
1.1 jdf 72: dedicated to RAIDframe support. Depending on the nature of the problem, posts
73: tend to end up in a variety of lists. At a very minimum, search
74: [netbsd-help](http://mail-index.NetBSD.org/netbsd-help/),
75: [netbsd-users@NetBSD.org](http://mail-index.NetBSD.org/netbsd-users/),
76: [current-users@NetBSD.org](http://mail-index.NetBSD.org/current-users/). Also
77: search the list for the NetBSD platform on which you are using RAIDframe:
78: port-*`${ARCH}`*@NetBSD.org.
79:
1.7 jdf 80: *Caution*: Because RAIDframe is constantly undergoing development, some information in
1.1 jdf 81: mailing list archives has the potential of being dated and inaccurate.
82:
1.6 jdf 83: 3. Search the [Problem Report
1.1 jdf 84: database](http://www.NetBSD.org/support/send-pr.html).
85:
1.6 jdf 86: 4. If your problem persists: Post to the mailing list most appropriate
87: (judgment call). Collect as much verbosely detailed information as possible
88: before posting: Include your
89: [dmesg(8)](http://netbsd.gw.com/cgi-bin/man-cgi?dmesg+8+NetBSD-5.0.1+i386)
90: output from `/var/run/dmesg.boot`, your kernel
91: [config(5)](http://netbsd.gw.com/cgi-bin/man-cgi?config+5+NetBSD-5.0.1+i386) ,
92: your `/etc/raid[0-9].conf`, any relevant errors on `/dev/console`,
93: `/var/log/messages`, or to `stdout/stderr` of
94: [raidctl(8)](http://netbsd.gw.com/cgi-bin/man-cgi?raidctl+8+NetBSD-5.0.1+i386).
95: The output of **raidctl -s** (if available) will be useful as well. Also
96: include details on the troubleshooting steps you've taken thus far, exactly
97: when the problem started, and any notes on recent changes that may have
98: prompted the problem to develop. Remember to be patient when waiting for a
1.1 jdf 99: response.
100:
101: ## Setup RAIDframe Support
102:
103: The use of RAID will require software and hardware configuration changes.
104:
105: ### Kernel Support
106:
1.6 jdf 107: The GENERIC kernel already has support for RAIDframe. If you have built a custom
108: kernel for your environment the kernel configuration must have the following
1.1 jdf 109: options:
110:
111: pseudo-device raid 8 # RAIDframe disk driver
112: options RAID_AUTOCONFIG # auto-configuration of RAID components
113:
1.6 jdf 114: The RAID support must be detected by the NetBSD kernel, which can be checked by
115: looking at the output of the
116: [dmesg(8)](http://netbsd.gw.com/cgi-bin/man-cgi?dmesg+8+NetBSD-5.0.1+i386)
1.1 jdf 117: command.
118:
119: # dmesg|grep -i raid
120: Kernelized RAIDframe activated
121:
1.6 jdf 122: Historically, the kernel must also contain static mappings between bus addresses
123: and device nodes in `/dev`. This used to ensure consistency of devices within
124: RAID sets in the event of a device failure after reboot. Since NetBSD 1.6,
125: however, using the auto-configuration features of RAIDframe has been recommended
126: over statically mapping devices. The auto-configuration features allow drives to
127: move around on the system, and RAIDframe will automatically determine which
1.1 jdf 128: components belong to which RAID sets.
129:
130: ### Power Redundancy and Disk Caching
131:
1.6 jdf 132: If your system has an Uninterruptible Power Supply (UPS), if your system has
133: redundant power supplies, or your disk controller has a battery, you should
134: consider enabling the read and write caches on your drives. On systems with
135: redundant power, this will improve drive performance. On systems without
136: redundant power, the write cache could endanger the integrity of RAID data in
1.1 jdf 137: the event of a power loss.
138:
1.6 jdf 139: The [dkctl(8)](http://netbsd.gw.com/cgi-bin/man-cgi?dkctl+8+NetBSD-5.0.1+i386)
140: utility to can be used for this on all kinds of disks that support the operation
1.1 jdf 141: (SCSI, EIDE, SATA, ...):
142:
143: # dkctl wd0 getcache
144: /dev/rwd0d: read cache enabled
145: /dev/rwd0d: read cache enable is not changeable
146: /dev/rwd0d: write cache enable is changeable
147: /dev/rwd0d: cache parameters are not savable
148: # dkctl wd0 setcache rw
149: # dkctl wd0 getcache
150: /dev/rwd0d: read cache enabled
151: /dev/rwd0d: write-back cache enabled
152: /dev/rwd0d: read cache enable is not changeable
153: /dev/rwd0d: write cache enable is changeable
154: /dev/rwd0d: cache parameters are not savable
155:
156: ## Example: RAID-1 Root Disk
157:
1.6 jdf 158: This example explains how to setup RAID-1 root disk. With RAID-1 components are
159: mirrored and therefore the server can be fully functional in the event of a
160: single component failure. The goal is to provide a level of redundancy that will
161: allow the system to encounter a component failure on either component disk in
1.1 jdf 162: the RAID and:
163:
164: * Continue normal operations until a maintenance window can be scheduled.
1.6 jdf 165: * Or, in the unlikely event that the component failure causes a system reboot,
1.1 jdf 166: be able to quickly reconfigure the system to boot from the remaining
167: component (platform dependent).
168:
1.9 jdf 169: 
1.1 jdf 170: **RAID-1 Disk Logical Layout**
171:
1.6 jdf 172: Because RAID-1 provides both redundancy and performance improvements, its most
173: practical application is on critical "system" partitions such as `/`, `/usr`,
174: `/var`, `swap`, etc., where read operations are more frequent than write
175: operations. For other file systems, such as `/home` or `/var/`, other RAID
176: levels might be considered (see the references above). If one were simply
177: creating a generic RAID-1 volume for a non-root file system, the cookie-cutter
178: examples from the man page could be followed, but because the root volume must
1.1 jdf 179: be bootable, certain special steps must be taken during initial setup.
180:
1.6 jdf 181: *Note*: This example will outline a process that differs only slightly between
182: the i386 and sparc64 platforms. In an attempt to reduce excessive duplication of
183: content, where differences do exist and are cosmetic in nature, they will be
184: pointed out using a section such as this. If the process is drastically
1.1 jdf 185: different, the process will branch into separate, platform dependent steps.
186:
187: ### Pseudo-Process Outline
188:
1.6 jdf 189: Although a much more refined process could be developed using a custom copy of
190: NetBSD installed on custom-developed removable media, presently the NetBSD
1.1 jdf 191: install media lacks RAIDframe tools and support, so the following pseudo process
192: has become the de facto standard for setting up RAID-1 Root.
193:
194: 1. Install a stock NetBSD onto Disk0 of your system.
195:
1.6 jdf 196:
1.9 jdf 197: 
1.1 jdf 198: **Perform generic install onto Disk0/wd0**
199:
1.6 jdf 200: 2. Use the installed system on Disk0/wd0 to setup a RAID Set composed of
1.1 jdf 201: Disk1/wd1 only.
202:
1.9 jdf 203: 
1.1 jdf 204: **Setup RAID Set**
205:
206: 3. Reboot the system off the Disk1/wd1 with the newly created RAID volume.
207:
1.6 jdf 208:
1.9 jdf 209: 
1.6 jdf 210: **Reboot using Disk1/wd1 of RAID**
1.5 jdf 211:
1.1 jdf 212:
1.7 jdf 213: 4. Add/re-sync Disk0/wd0 back into the RAID set.
1.1 jdf 214:
1.9 jdf 215: 
1.1 jdf 216: **Mirror Disk1/wd1 back to Disk0/wd0**
217:
218: ### Hardware Review
219:
1.6 jdf 220: At present, the alpha, amd64, i386, pmax, sparc, sparc64, and vax NetBSD
221: platforms support booting from RAID-1. Booting is not supported from any other
222: RAID level. Booting from a RAID set is accomplished by teaching the 1st stage
223: boot loader to understand both 4.2BSD/FFS and RAID partitions. The 1st boot
224: block code only needs to know enough about the disk partitions and file systems
225: to be able to read the 2nd stage boot blocks. Therefore, at any time, the
1.7 jdf 226: system's BIOS/firmware must be able to read a drive with 1st stage boot blocks
1.6 jdf 227: installed. On the i386 platform, configuring this is entirely dependent on the
1.7 jdf 228: vendor of the controller card/host bus adapter to which your disks are
1.1 jdf 229: connected. On sparc64 this is controlled by the IEEE 1275 Sun OpenBoot Firmware.
230:
1.6 jdf 231: This article assumes two identical IDE disks (`/dev/wd{0,1}`) which we are going
1.1 jdf 232: to mirror (RAID-1). These disks are identified as:
233:
234: # grep ^wd /var/run/dmesg.boot
235: wd0 at atabus0 drive 0: <WDC WD100BB-75CLB0>
236: wd0: drive supports 16-sector PIO transfers, LBA addressing
237: wd0: 9541 MB, 19386 cyl, 16 head, 63 sec, 512 bytes/sect x 19541088 sectors
238: wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
239: wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
240:
241: wd1 at atabus1 drive 0: <WDC WD100BB-75CLB0>
242: wd1: drive supports 16-sector PIO transfers, LBA addressing
243: wd1: 9541 MB, 19386 cyl, 16 head, 63 sec, 512 bytes/sect x 19541088 sectors
244: wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
245: wd1(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA data transfers)
246:
1.6 jdf 247: *Note*: If you are using SCSI, replace `/dev/{,r}wd{0,1}` with
248: `/dev/{,r}sd{0,1}`.
1.1 jdf 249:
1.6 jdf 250: In this example, both disks are jumpered as Master on separate channels on the
251: same controller. You usually wouldn't want to have both disks on the same bus on
252: the same controller; this creates a single point of failure. Ideally you would
253: have the disks on separate channels on separate controllers. Nonetheless, in
254: most cases the most critical point is the hard disk, so having redundant
255: channels or controllers is not that important. Plus, having more channels or
256: controllers increases costs. Some SCSI controllers have multiple channels on the
257: same controller, however, a SCSI bus reset on one channel could adversely affect
258: the other channel if the ASIC/IC becomes overloaded. The trade-off with two
259: controllers is that twice the bandwidth is used on the system bus. For purposes
260: of simplification, this example shows two disks on different channels on the
1.1 jdf 261: same controller.
262:
1.6 jdf 263: *Note*: RAIDframe requires that all components be of the same size. Actually, it
264: will use the lowest common denominator among components of dissimilar sizes. For
265: purposes of illustration, the example uses two disks of identical geometries.
266: Also, consider the availability of replacement disks if a component suffers a
1.1 jdf 267: critical hardware failure.
268:
1.6 jdf 269: *Tip*: Two disks of identical vendor model numbers could have different
270: geometries if the drive possesses "grown defects". Use a low-level program to
271: examine the grown defects table of the disk. These disks are obviously
1.1 jdf 272: suboptimal candidates for use in RAID and should be avoided.
273:
274: ### Initial Install on Disk0/wd0
275:
1.6 jdf 276: Perform a very generic installation onto your Disk0/wd0. Follow the `INSTALL`
277: instructions for your platform. Install all the sets but do not bother
1.1 jdf 278: customizing anything other than the kernel as it will be overwritten.
279:
1.6 jdf 280: *Tip*: On i386, during the sysinst install, when prompted if you want to `use
1.1 jdf 281: the entire disk for NetBSD`, answer `yes`.
282:
1.3 jdf 283: * [Installing NetBSD: Preliminary considerations and preparations](/guide/inst)
1.6 jdf 284: * [NetBSD/i386 Install](http://ftp.NetBSD.org/pub/NetBSD/NetBSD-5.0.2/i386/INSTALL.html)
285: * [NetBSD/sparc64 Install](http://ftp.NetBSD.org/pub/NetBSD/NetBSD-5.0.2/sparc64/INSTALL.html)
1.1 jdf 286:
1.6 jdf 287: Once the installation is complete, you should examine the
288: [disklabel(8)](http://netbsd.gw.com/cgi-bin/man-cgi?disklabel+8+NetBSD-5.0.1+i386)
289: and [fdisk(8)](http://netbsd.gw.com/cgi-bin/man-cgi?fdisk+8+NetBSD-5.0.1+i386) /
290: [sunlabel(8)](http://netbsd.gw.com/cgi-bin/man-cgi?sunlabel+8+NetBSD-5.0.1+i386)
1.1 jdf 291: outputs on the system:
292:
293: # df
294: Filesystem 1K-blocks Used Avail %Cap Mounted on
295: /dev/wd0a 9487886 502132 8511360 5% /
296:
297: On i386:
298:
299: # disklabel -r wd0
300: type: unknown
301: disk: Disk00
302: label:
303: flags:
304: bytes/sector: 512
305: sectors/track: 63
306: tracks/cylinder: 16
307: sectors/cylinder: 1008
308: cylinders: 19386
309: total sectors: 19541088
310: rpm: 3600
311: interleave: 1
312: trackskew: 0
313: cylinderskew: 0
314: headswitch: 0 # microseconds
315: track-to-track seek: 0 # microseconds
316: drivedata: 0
317:
318: 16 partitions:
319: # size offset fstype [fsize bsize cpg/sgs]
320: a: 19276992 63 4.2BSD 1024 8192 46568 # (Cyl. 0* - 19124*)
321: b: 264033 19277055 swap # (Cyl. 19124* - 19385)
322: c: 19541025 63 unused 0 0 # (Cyl. 0* - 19385)
323: d: 19541088 0 unused 0 0 # (Cyl. 0 - 19385)
324:
325: # fdisk /dev/rwd0d
326: Disk: /dev/rwd0d
327: NetBSD disklabel disk geometry:
328: cylinders: 19386, heads: 16, sectors/track: 63 (1008 sectors/cylinder)
329: total sectors: 19541088
330:
331: BIOS disk geometry:
332: cylinders: 1023, heads: 255, sectors/track: 63 (16065 sectors/cylinder)
333: total sectors: 19541088
334:
335: Partition table:
336: 0: NetBSD (sysid 169)
337: start 63, size 19541025 (9542 MB, Cyls 0-1216/96/1), Active
338: 1: <UNUSED>
339: 2: <UNUSED>
340: 3: <UNUSED>
341: Bootselector disabled.
342: First active partition: 0
343:
344: On Sparc64 the command and output differ slightly:
345:
346: # disklabel -r wd0
347: type: unknown
348: disk: Disk0
349: [...snip...]
350: 8 partitions:
351: # size offset fstype [fsize bsize cpg/sgs]
352: a: 19278000 0 4.2BSD 1024 8192 46568 # (Cyl. 0 - 19124)
353: b: 263088 19278000 swap # (Cyl. 19125 - 19385)
354: c: 19541088 0 unused 0 0 # (Cyl. 0 - 19385)
355:
356: # sunlabel /dev/rwd0c
357: sunlabel> P
358: a: start cyl = 0, size = 19278000 (19125/0/0 - 9413.09Mb)
359: b: start cyl = 19125, size = 263088 (261/0/0 - 128.461Mb)
360: c: start cyl = 0, size = 19541088 (19386/0/0 - 9541.55Mb)
361:
362: ### Preparing Disk1/wd1
363:
1.6 jdf 364: Once you have a stock install of NetBSD on Disk0/wd0, you are ready to begin.
365: Disk1/wd1 will be visible and unused by the system. To setup Disk1/wd1, you will
366: use
367: [disklabel(8)](http://netbsd.gw.com/cgi-bin/man-cgi?disklabel+8+NetBSD-5.0.1+i386)
1.1 jdf 368: to allocate the entire second disk to the RAID-1 set.
369:
1.6 jdf 370: *Tip*: The best way to ensure that Disk1/wd1 is completely empty is to 'zero'
371: out the first few sectors of the disk with
372: [dd(1)](http://netbsd.gw.com/cgi-bin/man-cgi?dd+1+NetBSD-5.0.1+i386) . This will
373: erase the MBR (i386) or Sun disk label (sparc64), as well as the NetBSD disk
374: label. If you make a mistake at any point during the RAID setup process, you can
1.1 jdf 375: always refer to this process to restore the disk to an empty state.
376:
377: *Note*: On sparc64, use `/dev/rwd1c` instead of `/dev/rwd1d`!
378:
379: # dd if=/dev/zero of=/dev/rwd1d bs=8k count=1
380: 1+0 records in
381: 1+0 records out
382: 8192 bytes transferred in 0.003 secs (2730666 bytes/sec)
383:
1.6 jdf 384: Once this is complete, on i386, verify that both the MBR and NetBSD disk labels
1.1 jdf 385: are gone. On sparc64, verify that the Sun Disk label is gone as well.
386:
387: On i386:
388:
389: # fdisk /dev/rwd1d
390:
391: fdisk: primary partition table invalid, no magic in sector 0
392: Disk: /dev/rwd1d
393: NetBSD disklabel disk geometry:
394: cylinders: 19386, heads: 16, sectors/track: 63 (1008 sectors/cylinder)
395: total sectors: 19541088
396:
397: BIOS disk geometry:
398: cylinders: 1023, heads: 255, sectors/track: 63 (16065 sectors/cylinder)
399: total sectors: 19541088
400:
401: Partition table:
402: 0: <UNUSED>
403: 1: <UNUSED>
404: 2: <UNUSED>
405: 3: <UNUSED>
406: Bootselector disabled.
407:
408: # disklabel -r wd1
409:
410: [...snip...]
411: 16 partitions:
412: # size offset fstype [fsize bsize cpg/sgs]
413: c: 19541025 63 unused 0 0 # (Cyl. 0* - 19385)
414: d: 19541088 0 unused 0 0 # (Cyl. 0 - 19385)
415:
416: On sparc64:
417:
418: # sunlabel /dev/rwd1c
419:
420: sunlabel: bogus label on `/dev/wd1c' (bad magic number)
421:
422: # disklabel -r wd1
423:
424: [...snip...]
425: 3 partitions:
426: # size offset fstype [fsize bsize cpg/sgs]
427: c: 19541088 0 unused 0 0 # (Cyl. 0 - 19385)
428: disklabel: boot block size 0
429: disklabel: super block size 0
430:
1.6 jdf 431: Now that you are certain the second disk is empty, on i386 you must establish
432: the MBR on the second disk using the values obtained from Disk0/wd0 above. We
433: must remember to mark the NetBSD partition active or the system will not boot.
434: You must also create a NetBSD disklabel on Disk1/wd1 that will enable a RAID
435: volume to exist upon it. On sparc64, you will need to simply
436: [disklabel(8)](http://netbsd.gw.com/cgi-bin/man-cgi?disklabel+8+NetBSD-5.0.1+i386)
1.1 jdf 437: the second disk which will write the proper Sun Disk Label.
438:
1.6 jdf 439: *Tip*:
440: [disklabel(8)](http://netbsd.gw.com/cgi-bin/man-cgi?disklabel+8+NetBSD-5.0.1+i386)
441: will use your shell' s environment variable `$EDITOR` variable to edit the
442: disklabel. The default is
1.1 jdf 443: [vi(1)](http://netbsd.gw.com/cgi-bin/man-cgi?vi+1+NetBSD-5.0.1+i386)
444:
445: On i386:
446:
447: # fdisk -0ua /dev/rwd1d
448: fdisk: primary partition table invalid, no magic in sector 0
449: Disk: /dev/rwd1d
450: NetBSD disklabel disk geometry:
451: cylinders: 19386, heads: 16, sectors/track: 63 (1008 sectors/cylinder)
452: total sectors: 19541088
453:
454: BIOS disk geometry:
455: cylinders: 1023, heads: 255, sectors/track: 63 (16065 sectors/cylinder)
456: total sectors: 19541088
457:
458: Do you want to change our idea of what BIOS thinks? [n]
459:
460: Partition 0:
461: <UNUSED>
462: The data for partition 0 is:
463: <UNUSED>
464: sysid: [0..255 default: 169]
465: start: [0..1216cyl default: 63, 0cyl, 0MB]
466: size: [0..1216cyl default: 19541025, 1216cyl, 9542MB]
467: bootmenu: []
468: Do you want to change the active partition? [n] y
469: Choosing 4 will make no partition active.
470: active partition: [0..4 default: 0] 0
471: Are you happy with this choice? [n] y
472:
473: We haven't written the MBR back to disk yet. This is your last chance.
474: Partition table:
475: 0: NetBSD (sysid 169)
476: start 63, size 19541025 (9542 MB, Cyls 0-1216/96/1), Active
477: 1: <UNUSED>
478: 2: <UNUSED>
479: 3: <UNUSED>
480: Bootselector disabled.
481: Should we write new partition table? [n] y
482:
483: # disklabel -r -e -I wd1
484: type: unknown
485: disk: Disk1
486: label:
487: flags:
488: bytes/sector: 512
489: sectors/track: 63
490: tracks/cylinder: 16
491: sectors/cylinder: 1008
492: cylinders: 19386
493: total sectors: 19541088
494: [...snip...]
495: 16 partitions:
496: # size offset fstype [fsize bsize cpg/sgs]
497: a: 19541025 63 RAID # (Cyl. 0*-19385)
498: c: 19541025 63 unused 0 0 # (Cyl. 0*-19385)
499: d: 19541088 0 unused 0 0 # (Cyl. 0 -19385)
500:
501: On sparc64:
502:
503: # disklabel -r -e -I wd1
504: type: unknown
505: disk: Disk1
506: label:
507: flags:
508: bytes/sector: 512
509: sectors/track: 63
510: tracks/cylinder: 16
511: sectors/cylinder: 1008
512: cylinders: 19386
513: total sectors: 19541088
514: [...snip...]
515: 3 partitions:
516: # size offset fstype [fsize bsize cpg/sgs]
517: a: 19541088 0 RAID # (Cyl. 0 - 19385)
518: c: 19541088 0 unused 0 0 # (Cyl. 0 - 19385)
519:
1.6 jdf 520: # sunlabel /dev/rwd1c
1.1 jdf 521: sunlabel> P
522: a: start cyl = 0, size = 19541088 (19386/0/0 - 9541.55Mb)
523: c: start cyl = 0, size = 19541088 (19386/0/0 - 9541.55Mb)
524:
1.6 jdf 525: *Note*: On i386, the `c:` and `d:` slices are reserved. `c:` represents the
526: NetBSD portion of the disk. `d:` represents the entire disk. Because we want to
527: allocate the entire NetBSD MBR partition to RAID, and because `a:` resides
528: within the bounds of `c:`, the `a:` and `c:` slices have same size and offset
529: values and sizes. The offset must start at a track boundary (an increment of
530: sectors matching the sectors/track value in the disk label). On sparc64 however,
531: `c:` represents the entire NetBSD partition in the Sun disk label and `d:` is
532: not reserved. Also note that sparc64's `c:` and `a:` require no offset from the
533: beginning of the disk, however if they should need to be, the offset must start
534: at a cylinder boundary (an increment of sectors matching the sectors/cylinder
1.1 jdf 535: value).
536:
537: ### Initializing the RAID Device
538:
1.7 jdf 539: Next we create the configuration file for the RAID set/volume. Traditionally,
1.6 jdf 540: RAIDframe configuration files belong in `/etc` and would be read and initialized
541: at boot time, however, because we are creating a bootable RAID volume, the
542: configuration data will actually be written into the RAID volume using the
543: *auto-configure* feature. Therefore, files are needed only during the initial
1.1 jdf 544: setup and should not reside in `/etc`.
545:
546: # vi /var/tmp/raid0.conf
547: START array
548: 1 2 0
549:
550: START disks
551: absent
552: /dev/wd1a
553:
554: START layout
555: 128 1 1 1
556:
557: START queue
558: fifo 100
559:
1.6 jdf 560: Note that `absent` means a non-existing disk. This will allow us to establish
561: the RAID volume with a bogus component that we will substitute for Disk0/wd0 at
1.1 jdf 562: a later time.
563:
1.6 jdf 564: Next we configure the RAID device and initialize the serial number to something
565: unique. In this example we use a "YYYYMMDD*`Revision`*" scheme. The format you
566: choose is entirely at your discretion, however the scheme you choose should
1.1 jdf 567: ensure that no two RAID sets use the same serial number at the same time.
568:
1.6 jdf 569: After that we initialize the RAID set for the first time, safely ignoring the
1.1 jdf 570: errors regarding the bogus component.
571:
572: # raidctl -v -C /var/tmp/raid0.conf raid0
573: Ignoring missing component at column 0
574: raid0: Component absent being configured at col: 0
575: Column: 0 Num Columns: 0
576: Version: 0 Serial Number: 0 Mod Counter: 0
577: Clean: No Status: 0
578: Number of columns do not match for: absent
579: absent is not clean!
580: raid0: Component /dev/wd1a being configured at col: 1
581: Column: 0 Num Columns: 0
582: Version: 0 Serial Number: 0 Mod Counter: 0
583: Clean: No Status: 0
584: Column out of alignment for: /dev/wd1a
585: Number of columns do not match for: /dev/wd1a
586: /dev/wd1a is not clean!
587: raid0: There were fatal errors
588: raid0: Fatal errors being ignored.
589: raid0: RAID Level 1
590: raid0: Components: component0[**FAILED**] /dev/wd1a
591: raid0: Total Sectors: 19540864 (9541 MB)
592: # raidctl -v -I 2009122601 raid0
593: # raidctl -v -i raid0
594: Initiating re-write of parity
595: raid0: Error re-writing parity!
596: Parity Re-write status:
597:
598: # tail -1 /var/log/messages
599: Dec 26 00:00:30 /netbsd: raid0: Error re-writing parity!
600: # raidctl -v -s raid0
601: Components:
602: component0: failed
603: /dev/wd1a: optimal
604: No spares.
605: component0 status is: failed. Skipping label.
606: Component label for /dev/wd1a:
607: Row: 0, Column: 1, Num Rows: 1, Num Columns: 2
608: Version: 2, Serial Number: 2009122601, Mod Counter: 7
609: Clean: No, Status: 0
610: sectPerSU: 128, SUsPerPU: 1, SUsPerRU: 1
611: Queue size: 100, blocksize: 512, numBlocks: 19540864
612: RAID Level: 1
613: Autoconfig: No
614: Root partition: No
615: Last configured as: raid0
616: Parity status: DIRTY
617: Reconstruction is 100% complete.
618: Parity Re-write is 100% complete.
619: Copyback is 100% complete.
620:
621: ### Setting up Filesystems
622:
1.6 jdf 623: *Caution*: The root filesystem must begin at sector 0 of the RAID device. If
1.1 jdf 624: not, the primary boot loader will be unable to find the secondary boot loader.
625:
1.6 jdf 626: The RAID device is now configured and available. The RAID device is a pseudo
627: disk-device. It will be created with a default disk label. You must now
628: determine the proper sizes for disklabel slices for your production environment.
629: For purposes of simplification in this example, our system will have 8.5
630: gigabytes dedicated to `/` as `/dev/raid0a` and the rest allocated to `swap`
1.1 jdf 631: as `/dev/raid0b`.
632:
1.6 jdf 633: *Caution*: This is an unrealistic disk layout for a production server; the
634: NetBSD Guide can expand on proper partitioning technique. See [Installing
1.1 jdf 635: NetBSD: Preliminary considerations and preparations*](inst).
636:
1.8 jdf 637: *Note*: 1 GB is 2\*1024\*1024=2097152 blocks (1 block is 512 bytes, or
1.6 jdf 638: 0.5 kilobytes). Despite what the underlying hardware composing a RAID set is,
1.1 jdf 639: the RAID pseudo disk will always have 512 bytes/sector.
640:
1.6 jdf 641: *Note*: In our example, the space allocated to the underlying `a:` slice
642: composing the RAID set differed between i386 and sparc64, therefore the total
1.1 jdf 643: sectors of the RAID volumes differs:
644:
645: On i386:
646:
647: # disklabel -r -e -I raid0
648: type: RAID
649: disk: raid
650: label: fictitious
651: flags:
652: bytes/sector: 512
653: sectors/track: 128
654: tracks/cylinder: 8
655: sectors/cylinder: 1024
656: cylinders: 19082
657: total sectors: 19540864
658: rpm: 3600
659: interleave: 1
660: trackskew: 0
661: cylinderskew: 0
662: headswitch: 0 # microseconds
663: track-to-track seek: 0 # microseconds
664: drivedata: 0
665:
666: # size offset fstype [fsize bsize cpg/sgs]
667: a: 19015680 0 4.2BSD 0 0 0 # (Cyl. 0 - 18569)
668: b: 525184 19015680 swap # (Cyl. 18570 - 19082*)
669: d: 19540864 0 unused 0 0 # (Cyl. 0 - 19082*)
670:
671: On sparc64:
672:
673: # disklabel -r -e -I raid0
674: [...snip...]
675: total sectors: 19539968
676: [...snip...]
677: 3 partitions:
678: # size offset fstype [fsize bsize cpg/sgs]
679: a: 19251200 0 4.2BSD 0 0 0 # (Cyl. 0 - 18799)
680: b: 288768 19251200 swap # (Cyl. 18800 - 19081)
681: c: 19539968 0 unused 0 0 # (Cyl. 0 - 19081)
682:
683: Next, format the newly created `/` partition as a 4.2BSD FFSv1 File System:
684:
685: # newfs -O 1 /dev/rraid0a
686: /dev/rraid0a: 9285.0MB (19015680 sectors) block size 16384, fragment size 2048
687: using 51 cylinder groups of 182.06MB, 11652 blks, 23040 inodes.
688: super-block backups (for fsck -b #) at:
689: 32, 372896, 745760, 1118624, 1491488, 1864352, 2237216, 2610080, 2982944,
690: ...............................................................................
691:
692: # fsck -fy /dev/rraid0a
693: ** /dev/rraid0a
694: ** File system is already clean
695: ** Last Mounted on
696: ** Phase 1 - Check Blocks and Sizes
697: ** Phase 2 - Check Pathnames
698: ** Phase 3 - Check Connectivity
699: ** Phase 4 - Check Reference Counts
700: ** Phase 5 - Check Cyl groups
701: 1 files, 1 used, 4679654 free (14 frags, 584955 blocks, 0.0% fragmentation)
702:
703: ### Migrating System to RAID
704:
1.6 jdf 705: The new RAID filesystems are now ready for use. We mount them under `/mnt` and
706: copy all files from the old system. This can be done using
707: [dump(8)](http://netbsd.gw.com/cgi-bin/man-cgi?dump+8+NetBSD-5.0.1+i386) or
1.1 jdf 708: [pax(1)](http://netbsd.gw.com/cgi-bin/man-cgi?pax+1+NetBSD-5.0.1+i386).
709:
710: # mount /dev/raid0a /mnt
711: # df -h /mnt
712: Filesystem Size Used Avail %Cap Mounted on
713: /dev/raid0a 8.9G 2.0K 8.5G 0% /mnt
714: # cd /; pax -v -X -rw -pe . /mnt
715: [...snip...]
716:
1.6 jdf 717: The NetBSD install now exists on the RAID filesystem. We need to fix the
718: mount-points in the new copy of `/etc/fstab` or the system will not come up
1.1 jdf 719: correctly. Replace instances of `wd0` with `raid0`.
720:
1.6 jdf 721: The swap should be unconfigured upon shutdown to avoid parity errors on the RAID
1.1 jdf 722: device. This can be done with a simple, one-line setting in `/etc/rc.conf`.
723:
724: # vi /mnt/etc/rc.conf
725: swapoff=YES
726:
1.6 jdf 727: Next, the boot loader must be installed on Disk1/wd1. Failure to install the
1.1 jdf 728: loader on Disk1/wd1 will render the system un-bootable if Disk0/wd0 fails. You
729: should hope your system won't have to reboot when wd0 fails.
730:
1.6 jdf 731: *Tip*: Because the BIOS/CMOS menus in many i386 based systems are misleading
732: with regard to device boot order. I highly recommend utilizing the `-o
733: timeout=X` option supported by the i386 1st stage boot loader. Setup unique
734: values for each disk as a point of reference so that you can easily determine
1.1 jdf 735: from which disk the system is booting.
736:
1.6 jdf 737: *Caution*: Although it may seem logical to install the 1st stage boot block into
738: `/dev/rwd1{c,d}` (which is historically correct with NetBSD 1.6.x
739: [installboot(8)](http://netbsd.gw.com/cgi-bin/man-cgi?installboot+8+NetBSD-5.0.1+i386)
740: , this is no longer the case. If you make this mistake, the boot sector will
1.1 jdf 741: become irrecoverably damaged and you will need to start the process over again.
742:
743: On i386, install the boot loader into `/dev/rwd1a`:
744:
745: # /usr/sbin/installboot -o timeout=30 -v /dev/rwd1a /usr/mdec/bootxx_ffsv1
746: File system: /dev/rwd1a
747: Primary bootstrap: /usr/mdec/bootxx_ffsv1
748: Ignoring PBR with invalid magic in sector 0 of `/dev/rwd1a'
749: Boot options: timeout 30, flags 0, speed 9600, ioaddr 0, console pc
750:
1.6 jdf 751: On sparc64, install the boot loader into `/dev/rwd1a` as well, however the `-o`
1.1 jdf 752: flag is unsupported (and un-needed thanks to OpenBoot):
753:
754: # /usr/sbin/installboot -v /dev/rwd1a /usr/mdec/bootblk
755: File system: /dev/rwd1a
756: Primary bootstrap: /usr/mdec/bootblk
757: Bootstrap start sector: 1
758: Bootstrap byte count: 5140
759: Writing bootstrap
760:
1.6 jdf 761: Finally the RAID set must be made auto-configurable and the system should be
1.1 jdf 762: rebooted. After the reboot everything is mounted from the RAID devices.
763:
764: # raidctl -v -A root raid0
765: raid0: Autoconfigure: Yes
766: raid0: Root: Yes
767: # tail -2 /var/log/messages
768: raid0: New autoconfig value is: 1
769: raid0: New rootpartition value is: 1
770: # raidctl -v -s raid0
771: [...snip...]
772: Autoconfig: Yes
773: Root partition: Yes
774: Last configured as: raid0
775: [...snip...]
776: # shutdown -r now
777:
1.7 jdf 778: *Warning*: Always use
1.6 jdf 779: [shutdown(8)](http://netbsd.gw.com/cgi-bin/man-cgi?shutdown+8+NetBSD-5.0.1+i386)
780: when shutting down. Never simply use
781: [reboot(8)](http://netbsd.gw.com/cgi-bin/man-cgi?reboot+8+NetBSD-5.0.1+i386).
1.5 jdf 782: [reboot(8)](http://netbsd.gw.com/cgi-bin/man-cgi?reboot+8+NetBSD-5.0.1+i386)
1.6 jdf 783: will not properly run shutdown RC scripts and will not safely disable swap. This
1.1 jdf 784: will cause dirty parity at every reboot.
785:
786: ### The first boot with RAID
787:
1.6 jdf 788: At this point, temporarily configure your system to boot Disk1/wd1. See notes in
789: [[Testing Boot Blocks|guide/rf#adding-text-boot]] for details on this process.
790: The system should boot now and all filesystems should be on the RAID devices.
791: The RAID will be functional with a single component, however the set is not
1.1 jdf 792: fully functional because the bogus drive (wd9) has failed.
793:
794: # egrep -i "raid|root" /var/run/dmesg.boot
795: raid0: RAID Level 1
796: raid0: Components: component0[**FAILED**] /dev/wd1a
797: raid0: Total Sectors: 19540864 (9541 MB)
798: boot device: raid0
799: root on raid0a dumps on raid0b
800: root file system type: ffs
801:
802: # df -h
803: Filesystem Size Used Avail Capacity Mounted on
804: /dev/raid0a 8.9G 196M 8.3G 2% /
805: kernfs 1.0K 1.0K 0B 100% /kern
806:
807: # swapctl -l
808: Device 1K-blocks Used Avail Capacity Priority
809: /dev/raid0b 262592 0 262592 0% 0
810: # raidctl -s raid0
811: Components:
812: component0: failed
813: /dev/wd1a: optimal
814: No spares.
815: component0 status is: failed. Skipping label.
816: Component label for /dev/wd1a:
817: Row: 0, Column: 1, Num Rows: 1, Num Columns: 2
818: Version: 2, Serial Number: 2009122601, Mod Counter: 65
819: Clean: No, Status: 0
820: sectPerSU: 128, SUsPerPU: 1, SUsPerRU: 1
821: Queue size: 100, blocksize: 512, numBlocks: 19540864
822: RAID Level: 1
823: Autoconfig: Yes
824: Root partition: Yes
825: Last configured as: raid0
826: Parity status: DIRTY
827: Reconstruction is 100% complete.
828: Parity Re-write is 100% complete.
829: Copyback is 100% complete.
830:
831: ### Adding Disk0/wd0 to RAID
832:
1.6 jdf 833: We will now add Disk0/wd0 as a component of the RAID. This will destroy the
834: original file system structure. On i386, the MBR disklabel will be unaffected
835: (remember we copied wd0's label to wd1 anyway) , therefore there is no need to
836: "zero" Disk0/wd0. However, we need to relabel Disk0/wd0 to have an identical
837: NetBSD disklabel layout as Disk1/wd1. Then we add Disk0/wd0 as "hot-spare" to
838: the RAID set and initiate the parity reconstruction for all RAID devices,
1.1 jdf 839: effectively bringing Disk0/wd0 into the RAID-1 set and "syncing up" both disks.
840:
841: # disklabel -r wd1 > /tmp/disklabel.wd1
842: # disklabel -R -r wd0 /tmp/disklabel.wd1
843:
1.6 jdf 844: As a last-minute sanity check, you might want to use
845: [diff(1)](http://netbsd.gw.com/cgi-bin/man-cgi?diff+1+NetBSD-5.0.1+i386) to
846: ensure that the disklabels of Disk0/wd0 match Disk1/wd1. You should also backup
1.1 jdf 847: these files for reference in the event of an emergency.
848:
849: # disklabel -r wd0 > /tmp/disklabel.wd0
850: # disklabel -r wd1 > /tmp/disklabel.wd1
851: # diff /tmp/disklabel.wd0 /tmp/disklabel.wd1
852: # fdisk /dev/rwd0 > /tmp/fdisk.wd0
853: # fdisk /dev/rwd1 > /tmp/fdisk.wd1
854: # diff /tmp/fdisk.wd0 /tmp/fdisk.wd1
855: # mkdir /root/RFbackup
856: # cp -p /tmp/{disklabel,fdisk}* /root/RFbackup
857:
858: Once you are sure, add Disk0/wd0 as a spare component, and start reconstruction:
859:
860: # raidctl -v -a /dev/wd0a raid0
861: /netbsd: Warning: truncating spare disk /dev/wd0a to 241254528 blocks
862: # raidctl -v -s raid0
863: Components:
864: component0: failed
865: /dev/wd1a: optimal
866: Spares:
867: /dev/wd0a: spare
868: [...snip...]
869: # raidctl -F component0 raid0
870: RECON: initiating reconstruction on col 0 -> spare at col 2
871: 11% |**** | ETA: 04:26 \
872:
1.6 jdf 873: Depending on the speed of your hardware, the reconstruction time will vary. You
1.1 jdf 874: may wish to watch it on another terminal (note that you can interrupt
875: `raidctl -S` any time without stopping the synchronisation):
876:
877: # raidctl -S raid0
878: Reconstruction is 0% complete.
879: Parity Re-write is 100% complete.
880: Copyback is 100% complete.
881: Reconstruction status:
882: 17% |****** | ETA: 03:08 -
883:
884: After reconstruction, both disks should be *optimal*.
885:
886: # tail -f /var/log/messages
887: raid0: Reconstruction of disk at col 0 completed
888: raid0: Recon time was 1290.625033 seconds, accumulated XOR time was 0 us (0.000000)
889: raid0: (start time 1093407069 sec 145393 usec, end time 1093408359 sec 770426 usec)
890: raid0: Total head-sep stall count was 0
891: raid0: 305318 recon event waits, 1 recon delays
892: raid0: 1093407069060000 max exec ticks
893:
894: # raidctl -v -s raid0
895: Components:
896: component0: spared
897: /dev/wd1a: optimal
898: Spares:
899: /dev/wd0a: used_spare
900: [...snip...]
901:
1.6 jdf 902: When the reconstruction is finished we need to install the boot loader on the
1.1 jdf 903: Disk0/wd0. On i386, install the boot loader into `/dev/rwd0a`:
904:
905: # /usr/sbin/installboot -o timeout=15 -v /dev/rwd0a /usr/mdec/bootxx_ffsv1
906: File system: /dev/rwd0a
907: Primary bootstrap: /usr/mdec/bootxx_ffsv1
908: Boot options: timeout 15, flags 0, speed 9600, ioaddr 0, console pc
909:
910: On sparc64:
911:
912: # /usr/sbin/installboot -v /dev/rwd0a /usr/mdec/bootblk
913: File system: /dev/rwd0a
914: Primary bootstrap: /usr/mdec/bootblk
915: Bootstrap start sector: 1
916: Bootstrap byte count: 5140
917: Writing bootstrap
918:
1.6 jdf 919: And finally, reboot the machine one last time before proceeding. This is
920: required to migrate Disk0/wd0 from status "used\_spare" as "Component0" to state
921: "optimal". Refer to notes in the next section regarding verification of clean
1.1 jdf 922: parity after each reboot.
923:
924: # shutdown -r now
925:
926: ### Testing Boot Blocks
927:
1.6 jdf 928: At this point, you need to ensure that your system's hardware can properly boot
929: using the boot blocks on either disk. On i386, this is a hardware-dependent
930: process that may be done via your motherboard CMOS/BIOS menu or your controller
1.1 jdf 931: card's configuration menu.
932:
1.6 jdf 933: On i386, use the menu system on your machine to set the boot device order /
934: priority to Disk1/wd1 before Disk0/wd0. The examples here depict a generic Award
935:
1.1 jdf 936: BIOS.
937:
1.9 jdf 938: 
1.1 jdf 939: **Award BIOS i386 Boot Disk1/wd1**
940:
941: Save changes and exit:
942:
943: >> NetBSD/i386 BIOS Boot, Revision 5.2 (from NetBSD 5.0.2)
944: >> (builds@b7, Sun Feb 7 00:30:50 UTC 2010)
945: >> Memory: 639/130048 k
946: Press return to boot now, any other key for boot menu
947: booting hd0a:netbsd - starting in 30
948:
1.5 jdf 949: You can determine that the BIOS is reading Disk1/wd1 because the timeout of th
1.6 jdf 950:
1.5 jdf 951: boot loader is 30 seconds instead of 15. After the reboot, re-enter the BIOS an
1.1 jdf 952: configure the drive boot order back to the default:
953:
1.9 jdf 954: 
1.1 jdf 955: **Award BIOS i386 Boot Disk0/wd0**
956:
957: Save changes and exit:
958:
959: >> NetBSD/i386 BIOS Boot, Revision 5.2 (from NetBSD 5.0.2)
960: >> Memory: 639/130048 k
961: Press return to boot now, any other key for boot menu
962: booting hd0a:netbsd - starting in 15
963:
1.6 jdf 964: Notice how your custom kernel detects controller/bus/drive assignments
965: independent of what the BIOS assigns as the boot disk. This is the expected
1.1 jdf 966: behavior.
967:
968: On sparc64, use the Sun OpenBoot **devalias** to confirm that both disks are bootable:
969:
970: Sun Ultra 5/10 UPA/PCI (UltraSPARC-IIi 400MHz), No Keyboard
971: OpenBoot 3.15, 128 MB memory installed, Serial #nnnnnnnn.
972: Ethernet address 8:0:20:a5:d1:3b, Host ID: nnnnnnnn.
973:
974: ok devalias
975: [...snip...]
976: cdrom /pci@1f,0/pci@1,1/ide@3/cdrom@2,0:f
977: disk /pci@1f,0/pci@1,1/ide@3/disk@0,0
978: disk3 /pci@1f,0/pci@1,1/ide@3/disk@3,0
979: disk2 /pci@1f,0/pci@1,1/ide@3/disk@2,0
980: disk1 /pci@1f,0/pci@1,1/ide@3/disk@1,0
981: disk0 /pci@1f,0/pci@1,1/ide@3/disk@0,0
982: [...snip...]
983:
984: ok boot disk0 netbsd
985: Initializing Memory [...]
986: Boot device /pci/pci/ide@3/disk@0,0 File and args: netbsd
987: NetBSD IEEE 1275 Bootblock
988: >> NetBSD/sparc64 OpenFirmware Boot, Revision 1.13
989: >> (builds@b7.netbsd.org, Wed Jul 29 23:43:42 UTC 2009)
990: loadfile: reading header
991: elf64_exec: Booting [...]
992: symbols @ [....]
993: Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
994: 2006, 2007, 2008, 2009
995: The NetBSD Foundation, Inc. All rights reserved.
996: Copyright (c) 1982, 1986, 1989, 1991, 1993
997: The Regents of the University of California. All rights reserved.
998: [...snip...]
999:
1000: And the second disk:
1001:
1002: ok boot disk2 netbsd
1003: Initializing Memory [...]
1004: Boot device /pci/pci/ide@3/disk@2,0: File and args:netbsd
1005: NetBSD IEEE 1275 Bootblock
1006: >> NetBSD/sparc64 OpenFirmware Boot, Revision 1.13
1007: >> (builds@b7.netbsd.org, Wed Jul 29 23:43:42 UTC 2009)
1008: loadfile: reading header
1009: elf64_exec: Booting [...]
1010: symbols @ [....]
1011: Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
1012: 2006, 2007, 2008, 2009
1013: The NetBSD Foundation, Inc. All rights reserved.
1014: Copyright (c) 1982, 1986, 1989, 1991, 1993
1015: The Regents of the University of California. All rights reserved.
1016: [...snip...]
1017:
1.6 jdf 1018: At each boot, the following should appear in the NetBSD kernel
1.1 jdf 1019: [dmesg(8)](http://netbsd.gw.com/cgi-bin/man-cgi?dmesg+8+NetBSD-5.0.1+i386) :
1020:
1021: Kernelized RAIDframe activated
1022: raid0: RAID Level 1
1023: raid0: Components: /dev/wd0a /dev/wd1a
1024: raid0: Total Sectors: 19540864 (9541 MB)
1025: boot device: raid0
1026: root on raid0a dumps on raid0b
1027: root file system type: ffs
1028:
1.6 jdf 1029: Once you are certain that both disks are bootable, verify the RAID parity is
1.1 jdf 1030: clean after each reboot:
1031:
1032: # raidctl -v -s raid0
1033: Components:
1034: /dev/wd0a: optimal
1035: /dev/wd1a: optimal
1036: No spares.
1037: [...snip...]
1038: Component label for /dev/wd0a:
1039: Row: 0, Column: 0, Num Rows: 1, Num Columns: 2
1040: Version: 2, Serial Number: 2009122601, Mod Counter: 67
1041: Clean: No, Status: 0
1042: sectPerSU: 128, SUsPerPU: 1, SUsPerRU: 1
1043: Queue size: 100, blocksize: 512, numBlocks: 19540864
1044: RAID Level: 1
1045: Autoconfig: Yes
1046: Root partition: Yes
1047: Last configured as: raid0
1048: Component label for /dev/wd1a:
1049: Row: 0, Column: 1, Num Rows: 1, Num Columns: 2
1050: Version: 2, Serial Number: 2009122601, Mod Counter: 67
1051: Clean: No, Status: 0
1052: sectPerSU: 128, SUsPerPU: 1, SUsPerRU: 1
1053: Queue size: 100, blocksize: 512, numBlocks: 19540864
1054: RAID Level: 1
1055: Autoconfig: Yes
1056: Root partition: Yes
1057: Last configured as: raid0
1058: Parity status: clean
1059: Reconstruction is 100% complete.
1060: Parity Re-write is 100% complete.
1061: Copyback is 100% complete.
1062:
CVSweb for NetBSD wikisrc <wikimaster@NetBSD.org> software: FreeBSD-CVSweb
![[BACK]](/icons/back.gif){kind=icon}
Return to raidframe.mdwn CVS log ![[TXT]](/icons/text.gif){kind=icon}
![[DIR]](/icons/dir.gif){kind=icon}
Up to [NetBSD Developer Wiki] / wikisrc / guide